- 您現在的位置：買賣IC網 > PDF目錄382553 > ST7PDALIF2M6 (意法半導體) 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, TIMERS, SPI, DALI PDF資料下載
參數資料
| 型號： | ST7PDALIF2M6 |
| 廠商： | 意法半導體 |
| 元件分類： | ADC |
| 英文描述： | 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, TIMERS, SPI, DALI |
| 中文描述： | 8位單電壓閃存存儲器，數據EEPROM，模數轉換器，定時器，SPI和大理微控制器 |
| 文件頁數： | 40/141頁 |
| 文件大小： | 2175K |
| 代理商： | ST7PDALIF2M6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁
ST7DALI
40/141
1
POWER SAVING MODES
(Cont’d)
9.4 HALT MODE
The HALT mode is the lowest power consumption
mode of the MCU. It is entered by executing the
‘HALT’ instruction when ACTIVE-HALT is disabled
(see
section 9.5 on page 41
for more details) and
when the AWUEN bit in the AWUCSR register is
cleared.
The MCU can exit HALT mode on reception of ei-
ther a specific interrupt (see Table 5, “Interrupt
Mapping,” on page 35) or a RESET. When exiting
HALT mode by means of a RESET or an interrupt,
the oscillator is immediately turned on and the 256
or 4096 CPU cycle delay is used to stabilize the
oscillator. After the start up delay, the CPU
resumes operation by servicing the interrupt or by
fetching the reset vector which woke it up (see
Fig-
ure 24
).
When entering HALT mode, the I bit in the CC reg-
ister is forced to 0 to enable interrupts. Therefore,
if an interrupt is pending, the MCU wakes up im-
mediately.
In HALT mode, the main oscillator is turned off
causing all internal processing to be stopped, in-
cluding the operation of the on-chip peripherals.
All peripherals are not clocked except the ones
which get their clock supply from another clock
generator (such as an external or auxiliary oscilla-
tor).
The compatibility of Watchdog operation with
HALT mode is configured by the “WDGHALT” op-
tion bit of the option byte. The HALT instruction
when executed while the Watchdog system is en-
abled, can generate a Watchdog RESET (see
sec-
tion 15.1 on page 130
for more details).
Figure 23. HALT Timing Overview
Figure 24. HALT Mode Flow-chart
Notes:
1.
WDGHALT is an option bit. See option byte sec-
tion for more details.
2.
Peripheral clocked with an external clock source
can still be active.
3.
Only some specific interrupts can exit the MCU
from HALT mode (such as external interrupt). Re-
fer to
Table 5 Interrupt Mapping
for more details.
4.
Before servicing an interrupt, the CC register is
pushed on the stack. The I bit of the CC register is
set during the interrupt routine and cleared when-
the CC register is popped.
5.
If the PLL is enabled by option byte, it outputs
the clock after a delay of t
STARTUP
(see
Figure 11
).
HALT
RUN
RUN
256 OR 4096 CPU
CYCLE DELAY
RESET
OR
INTERRUPT
HALT
INSTRUCTION
[Active Halt disabled]
FETCH
VECTOR
RESET
INTERRUPT
3)
Y
N
N
Y
CPU
I BIT
OSCILLATOR
PERIPHERALS
2)
OFF
OFF
OFF
0
FETCH RESET VECTOR
OR SERVICE INTERRUPT
CPU
I BIT
OSCILLATOR
PERIPHERALS
ON
OFF
ON
X
4)
CPU
I BIT
OSCILLATOR
PERIPHERALS
ON
ON
ON
X
4)
256 OR 4096 CPU CLOCK
DELAY
5)
CYCLE
WATCHDOG
ENABLE
DISABLE
WDGHALT
1)
0
WATCHDOG
RESET
1
HALT
INSTRUCTION
(Active Halt disabled)
(AWUCSR.AWUEN=0)
相關PDF資料 |
PDF描述 |
|---|---|
| ST7FLCD1 | 8-bit MCU for LCD Monitors with 60 KBytes Flash, 2 KBytes RAM, 2 DDC Ports and Infrared Controller |
| ST7FLIT19B | 8-Bit MCU With Single Voltage Flash Memory, Data EEPROM, ADC, 5 Timers, SPI(內部RC,PLL,ADC,ROP,ICP, IAP,SPI的8位MCU) |
| ST7FLITE10F1B6 | 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, 4 TIMERS, SPI |
| ST7FLITE19F1M6 | CLUSTER PANEL,RJ-11 W/ (12) 4- |
| ST7LITE1 | 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, 4 TIMERS, SPI |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST7PF-DC24V | 制造商:Fuji Electric 功能描述: |
| ST7PL05Y0MAOJXRE | 制造商:STMicroelectronics 功能描述:SOCKET BOARD LITE - Tape and Reel |
| ST7PLITE02F0U6TR | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MICROCONTROLLER WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, TIMERS, SPI |
| ST7PLITE02Y0B6 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MICROCONTROLLER WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, TIMERS, SPI |
| ST7PLITE02Y0B6TR | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-bit microcontroller with single voltage Flash memory, data EEPROM, ADC, timers, SPI |
發布緊急采購，3分鐘左右您將得到回復。