- 您現在的位置：買賣IC網 > PDF目錄383840 > ST7LITE19F1M6 ST7LITE1 - 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY.DATA EEPROM. ADC. 4 TIMERS. SPI PDF資料下載
參數資料
| 型號： | ST7LITE19F1M6 |
| 英文描述： | ST7LITE1 - 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY.DATA EEPROM. ADC. 4 TIMERS. SPI |
| 中文描述： | ST7LITE1 - 8單電壓閃存EEPROM的MEMORY.DATA位MCU。 ADC的。 4定時器。的SPI |
| 文件頁數： | 79/122頁 |
| 文件大小： | 1716K |
| 代理商： | ST7LITE19F1M6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁當前第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁
ST7LITE0, ST7SUPERLITE
79/122
13.2 ABSOLUTE MAXIMUM RATINGS
Stresses above those listed as “absolute maxi-
mum ratings” may cause permanent damage to
the device. This is a stress rating only and func-
tional operation of the device under these condi-
13.2.1 Voltage Characteristics
tions is not implied. Exposure to maximum rating
conditions for extended periods may affect device
reliability.
13.2.2 Current Characteristics
13.2.3 Thermal Characteristics
Notes:
1. Directly connecting the RESET and I/O pins to V
or V
could damage the device if an unintentional internal reset
is generated or an unexpected change of the I/O configuration occurs (for example, due to a corrupted program counter).
To guarantee safe operation, this connection has to be done through a pull-up or pull-down resistor (typical: 4.7k
for
RESET, 10k
for I/Os). Unused I/O pins must be tied in the same way to V
DD
or V
SS
according to their reset configuration.
2. When the current limitation is not possible, the V
absolute maximum rating must be respected, otherwise refer to
I
INJ(PIN)
specification. A positive injection is induced by V
IN
>V
DD
while a negative injection is induced by V
IN
<V
SS
.
3. All power (V
DD
) and ground (V
SS
) lines must always be connected to the external supply.
4. Negative injection disturbs the analog performance of the device. In particular, it induces leakage currents throughout
the device including the analog inputs. To avoid undesirable effects on the analog functions, care must be taken:
- Analog input pins must have a negative injection less than 0.8 mA (assuming that the impedance of the analog voltage
is lower than the specified limits)
- Pure digital pins must have a negative injection less than 1.6mA. In addition, it is recommended to inject the current as
far as possible from the analog input pins.
5. When several inputs are submitted to a current injection, the maximum
Σ
I
is the absolute sum of the positive
and negative injected currents (instantaneous values). These results are based on characterisation with
Σ
I
INJ(PIN)
maxi-
mum current injection on four I/O port pins of the device.
6. True open drain I/O port pins do not accept positive injection.
Symbol
Ratings
Maximum value
Unit
V
DD
- V
SS
V
IN
V
ESD(HBM)
V
ESD(MM)
Supply voltage
Input voltage on any pin
1) & 2)
Electrostatic discharge voltage (Human Body Model)
Electrostatic discharge voltage (Machine Model)
7.0
V
V
SS
-0.3 to V
DD
+0.3
see
section 13.7.2 on page 91
Symbol
Ratings
Maximum value
Unit
I
VDD
I
VSS
Total current into V
DD
power lines (source)
3)
Total current out of V
SS
ground lines (sink)
3)
Output current sunk by any standard I/O and control pin
Output current sunk by any high sink I/O pin
Output current source by any I/Os and control pin
Injected current on RESET pin
Injected current on any other pin
5) & 6)
Total injected current (sum of all I/O and control pins)
5)
100
100
25
50
- 25
± 5
± 5
± 20
mA
I
IO
I
INJ(PIN) 2) & 4)
Σ
I
INJ(PIN) 2)
Symbol
Ratings
Value
Unit
T
STG
T
J
Storage temperature range
Maximum junction temperature (see
Section 14.2 THERMAL CHARACTERISTICS
)
-65 to +150
°C
1
相關PDF資料 |
PDF描述 |
|---|---|
| ST890B | 1.2 CURRENT LIMITED HIGH SIDE WITH THERMAL SHUTDOWN |
| ST890C | 1.2 CURRENT LIMITED HIGH SIDE WITH THERMAL SHUTDOWN |
| ST890 | 1.2A CURRENT LIMITED HIGH SIDE WITH THERMAL SHUTDOWN |
| ST8LR2 | PHOTOTRANSISTOR | NPN | 800NM PEAK WAVELENGTH | 20M | LED-2B |
| ST92R195C | ROMLESS HCMOS MCU WITH ON-SCREEN-DISPLAY AND TELETEXT DATA SLICER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST7LITE1XB | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, 5 TIMERS, SPI |
| ST7LITE1XB_08 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, 5 TIMERS, SPI |
| ST7LITE2 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MICROCONTROLLER WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, TIMERS, SPI |
| ST7LITE2_06 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MICROCONTROLLER WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, TIMERS, SPI |
| ST7LITE20 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, TIMERS, SPI |
發布緊急采購，3分鐘左右您將得到回復。