參數資料
型號： SN260Q
廠商： STMICROELECTRONICS
元件分類： 微控制器/微處理器
英文描述： LOCAL AREA NETWORK CONTROLLER, QCC40
封裝： 6 X 6 MM, 0.90 MM HEIGHT, ROHS COMPLIANT, MQ220, QFN-40
文件頁數： 17/47頁
文件大?。?/td> 1592K
代理商： SN260Q
SPI protocol
SN260
backup of data in the SN260. The SN260 will de-assert the nHOST_INT signal after
receiving a byte on the SPI. Due to inherent latency in the SN260, the timing of when the
nHOST_INT signal returns to idle can vary between transactions. nHOST_INT will always
return to idle for a minimum of 10s before asserting again. If the SN260 has more output
available after the transaction has completed, the nHOST_INT signal will assert again after
Slave Select is de-asserted and the Host must make another request.
7.2.5
Spacing
To ensure that the SN260 is always able to deal with incoming commands, a minimum inter-
command spacing is defined at 1ms. After every transaction, the Host must hold the Slave
Select high for a minimum of 1ms. The Host must respect the inter-command spacing
requirement, or the SN260 will not have time to operate on the command; additional
commands could result in error conditions or undesired behavior. If the nHOST_INT signal
is not already asserted, the Host is allowed to use the Wake handshake instead of the inter-
command spacing to determine if the SN260 is ready to accept a command.
7.2.6
Waking the SN260 from sleep
Waking up the SN260 involves a simple handshaking routine as illustrated in Figure 6. This
handshaking ensures that the Host will wait until the SN260 is fully awake and ready to
accept commands from the Host. If the SN260 is already awake when the handshake is
performed (such as when the Host resets and the SN260 is already operating), the
handshake will proceed as described below with no ill effects.
Note:
A wake handshake cannot be performed if nHOST_INT is already asserted.
Figure 6.
SN260 wake sequence
Waking the SN260 involves the following steps:
1.
Host asserts nWAKE.
2.
SN260 interrupts on nWAKE and exits sleep.
3.
SN260 performs all operations it needs to and will not respond until it is ready to accept
commands.
4.
SN260 asserts nHOST_INT within 10ms of nWAKE asserting. If the SN260 does not
assert nHOST_INT within 10ms of nWAKE, it is valid for the Host to consider the
SN260 unresponsive and to reset the SN260.
5.
Host detects nHOST_INT assertion. Since the assertion of nHOST_INT indicates the
SN260 can accept SPI transactions, the Host does not need to hold Slave Select high
for the normally required minimum 1ms of inter-command spacing.
6.
Host de-asserts nWAKE after detecting nHOST_INT assertion.
7.
SN260 will de-assert nHOST_INT within 25 s of nWAKE de-asserting.
8.
After 25s, any change on nHOST_INT will be an indication of a normal asynchronous
(callback) event.
相關PDF資料
PDF描述
SN54128J TTL/H/L SERIES, QUAD 2-INPUT NOR GATE, CDIP14
SNJ54128W TTL/H/L SERIES, QUAD 2-INPUT NOR GATE, CDFP14
SN54132J TTL/H/L SERIES, QUAD 2-INPUT NAND GATE, CDIP14
SN74S132N3 S SERIES, QUAD 2-INPUT NAND GATE, PDIP14
SN54175W TTL/H/L SERIES, POSITIVE EDGE TRIGGERED D FLIP-FLOP, COMPLEMENTARY OUTPUT, CDFP16
相關代理商/技術參數
參數描述
SN260QT 功能描述:射頻收發器 ZIGBEE 802.15.4 NETWORK PROCESSOR RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray
SN2634 制造商:Omron Corporation 功能描述:RELAY ASSEMBLY
SN26500PWR 制造商:Texas Instruments 功能描述:
SN27210DRKR 制造商:Texas Instruments 功能描述:Custom firmware of BQ27210
SN27322 制造商:Texas Instruments 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*