參數資料
型號： SL811S
廠商： CYPRESS SEMICONDUCTOR CORP
元件分類： 總線控制器
英文描述： USB Dual Speed Slave Controller
中文描述： UNIVERSAL SERIAL BUS CONTROLLER, PQCC28
封裝： PLASTIC, LCC-28
文件頁數： 9/27頁
文件大?。?/td> 181K
代理商： SL811S
SL811S/T
Document #: 38-08009 Rev. **
Page 9 of 27
Figure 4-2. 12-MHz Crystal Circuit.
4.10
SL811S/T has a built-in SOF (Start of Frame) Detect Interrupt signal that can be monitored by an external microprocessor. The
SOF indicates continuous USB activity and is transmitted by the USB Host every 1 ms (millisecond). The selected processor can
use its timer to track non-SOFs or non-USB activity, and thus start the power Suspend sequence. The peripheral requires
additional hardware to enable power shutdown to the SL811S/T, the removal of 3.3V power to USB Data+
line pull-up resistor,
(which signals a disconnect t the USB Host), and to turn-off the clock to the SL811S/T. In Suspend mode, the unit will draw less
than 40
μ
A (Micro-Amperes).
The SL811S/T can signal a wake-up to the Host USB device, providing the Pull-up resistor remains powered during the Suspend
time. A register control bit allows the SL811S/T to output a
‘
K
’
State on the USB to signal the Host. See Force Function description
in the Control Register Section. If the pull-up is powered down during Suspend, restoring power to the pull-up will signal a device
connect to the USB host.
Power Resume and Suspend Mode
4.11
Operation and control of the SL811S/T is managed through the internal registers. A portion of the internal RAM is devoted to the
register space and access is through the microprocessor interface. The registers provide control and status information for
transactions on the USB, microprocessor interface, DMA and interrupts.
SL811S/T Registers
4.12
The SL811S/T supports auto increment mode to reduce read and write memory cycles. In this mode, the microcontroller needs
to set up the address only once. Whenever any subsequent DATA is accessed, the internal address counter will advance to the
next address location.
Once the address of the starting location has been set, the write operations will write the data bytes in consecutive locations. For
example, assume the value Index1 was written into the Address register of SL811S/T during the Address cycle (with the A0 input
set low). The write operations in the data cycle (with A0 input set High) will write the data bytes into the sequential internal memory
locations Index1, Index1 + 1, Index1 + 2 and so on. The Auto increment mode also works on read operations from SL811S/T
operations. After setting the address of the starting location once, the read operations will read the subsequent internal memory
locations.
For example
Write 0x10 to SL811S/T in address cycle (A0 is set low)
Write 0x55 to SL811S/T in data cycle (A0 is set high) -> write 0x55 to location 0x10
Write 0xaa to SL811S/T in data cycle (A0 is set high) -> write 0xaa to location 0x11
Write 0xbb to SL811S/T in data cycle (A0 is set high) -> write 0xbb to location 0x12
Auto Address Increment Mode
X1
1 2MHz , series, 20-pF load
Rf
1M
Cin
22 pF
Cout
22 pF
Rs
100
X2
X1
相關PDF資料
PDF描述
SM-800 ECL
SM-801 ECL
SM-807 ECL
SM-809 ECL
SM-80A ECL
相關代理商/技術參數
參數描述
SL811S-DK 功能描述:TOOLS DEVELOPMENT FOR SL811 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035
SL811ST 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:SL811S/T USB Dual Speed Slave Controller
SL8203 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DCDC升壓IC
SL82184P12NF 功能描述:ANTENNA 850-1900MHZ 4DBI N FML RoHS:是 類別:RF/IF 和 RFID >> RF 天線 系列:* 標準包裝:1 系列:*
SL82184P36SMM 制造商:Laird Technologies Inc 功能描述:DUAL BAND, 850/1900 MHZ, 4 DBI CEILING MOUNT OMNIDIRECTIONAL ANTENNA WITH 36 OF COAXIAL CABLE AND TERMINATED IN A SMA MALE CONNECTOR.
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*