參數資料
型號: SE97BTP,547
廠商: NXP Semiconductors
文件頁數: 18/53頁
文件大?。?/td> 386K
描述: IC TEMP SENSOR DIMM 8HWSON
產品培訓模塊: I²C Bus Fundamentals
特色產品: NXP - I2C Interface
標準包裝: 1
功能: 溫度監控系統(傳感器),DIMM DDR 內存
傳感器類型: 內部
感應溫度: -40°C ~ 125°C
精確度: ±3°C(最小值)
拓撲: ADC(三角積分型),比較器,寄存器庫
輸出類型: I²C?/SMBus?
輸出警報:
輸出風扇:
電源電壓: 3 V ~ 3.6 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 8-WFDFN 裸露焊盤
供應商設備封裝: 8-WSON
包裝: 標準包裝
產品目錄頁面: 847 (CN2011-ZH PDF)
其它名稱: 568-5055-6
SE97B_1
?NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 01  27 January 2010
18 of 53
NXP Semiconductors
SE97B
DDR memory module temp sensor with integrated SPD
Up to eight memory devices can be connected on a single I
2
C-bus. Each one is given a
3-bit on the hardware selectable address (A2, A1, A0) inputs. The device only responds
when the 4-bit fixed and hardware selectable bits are matched. The 8th bit is the
read/write bit. This bit is set to 1 or 0 for read and write protection, respectively.
The corresponding device acknowledges during the ninth bit time when there is a match
on the 7-bit address.
The device does not acknowledge when there is no match on the 7-bit address or when
the device is already in permanent write protection mode and is programmed with any
write protection instructions (i.e., PWP, RWP, CWP).
 
 
7.10.2.1   Permanent Write Protection (PWP)
If the software write-protection has been set with the PWP instruction, the first 128 bytes
of the memory are permanently write-protected. This write-protection cannot be cleared
by any instruction, or by power-cycling the device. Also, once the PWP instruction has
been successfully executed, the device no longer acknowledges any instruction (with 4-bit
fixed address of 0110b) to access the write-protection settings.
X = Dont Care
(1)  Refer to Table 7
 regarding the exact state of the acknowledge bit.
Fig 13.   Software Write Protect (write)
1
1
0
A2
A1
A0
0
A
S
0
A
slave address (memory)
START condition
R/W
acknowledge
(1)
from slave
acknowledge
(1)
from slave
dummy byte address
SDA
dummy data
A
acknowledge
(1)
from slave
002aab356
P
STOP condition
X   X   X   X   X   X   X   X
X   X   X   X   X   X   X   X
X = Dont Care
(1)  Refer to Table 8
 regarding the exact state of the acknowledge bit.
Fig 14.   Software Write Protect (read)
1
1
0
A2
A1
A0
1
A
S
0
A
slave address (memory)
START condition
R/W
acknowledge
(1)
from slave
no acknowledge
(1)
from slave
dummy byte address
SDA
dummy data
A
no acknowledge
(1)
from slave
002aac644
P
STOP condition
X   X   X   X   X   X   X   X
X   X   X   X   X   X   X   X
相關PDF資料
PDF描述
SE98ATP,547 IC TEMP SENSOR DDR 8-HWSON
SG6901ASZ IC PFC CTLR AVERAGE CURR 20SOIC
SG6932SZ IC PFC CONTROLLER CCM 16SOP
SG6961SY IC PFC CTRLR AVERAGE CURR 8SOIC
SI3500-A-GM IC POE SWITCH PWR OVER LAN 20QFN
相關代理商/技術參數
參數描述
SE97PW 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:DDR memory module temp sensor with integrated SPD, 3.3 V
SE97PW,118 功能描述:板上安裝溫度傳感器 I2C LOCAL +/- 2OC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
SE97PW-T 功能描述:板上安裝溫度傳感器 I2C LOCAL +/- 2OC TS +SPD DIMM RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
SE97TK 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:DDR memory module temp sensor with integrated SPD, 3.3 V
SE97TK,118 功能描述:板上安裝溫度傳感器 I2C LOCAL +/- 2OC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor