- 您現在的位置：買賣IC網 > Datasheet目錄46 > SE97BTP,547 (NXP Semiconductors)IC TEMP SENSOR DIMM 8HWSON Datasheet資料下載
參數資料
| 型號： | SE97BTP,547 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 11/53頁 |
| 文件大?。?/td> | 386K |
| 描述： | IC TEMP SENSOR DIMM 8HWSON |
| 產品培訓模塊： | I²C Bus Fundamentals |
| 特色產品： | NXP - I2C Interface |
| 標準包裝： | 1 |
| 功能： | 溫度監控系統（傳感器），DIMM DDR 內存 |
| 傳感器類型： | 內部 |
| 感應溫度： | -40°C ~ 125°C |
| 精確度： | ±3°C（最小值） |
| 拓?fù)洌?/td> | ADC（三角積分型），比較器，寄存器庫 |
| 輸出類型： | I²C?/SMBus? |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-WFDFN 裸露焊盤 |
| 供應商設備封裝： | 8-WSON |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 847 (CN2011-ZH PDF) |
| 其它名稱： | 568-5055-6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁
SE97B_1
?NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 01 27 January 2010
11 of 53
NXP Semiconductors
SE97B
DDR memory module temp sensor with integrated SPD
7.4 Conversion rate
The conversion time is the amount of time required for the ADC to complete a
temperature measurement for the local temperature sensor. The conversion rate is the
inverse of the conversion period which describes the number of cycles the temperature
measurement completes in one secondthe faster the conversion rate, the faster the
temperature reading is updated. The SE97Bs conversion rate is at least 8 Hz or 125 ms.
7.4.1 What temperature is read when conversion is in progress
The SE97B has been designed to ensure a valid temperature is always available. When a
read to the temperature register is initiated through the SMBus, the device checks to see if
the temperature conversion process (Analog-to-Digital conversion) is complete and a new
temperature is available:
" If the temperature conversion process is complete, then the new temperature value is
sent out on the SMBus.
" If the temperature conversion process in not complete, then the previous temperature
value is sent out on the SMBus.
It is possible that while SMBus Master is reading the temperature register, a new
temperature conversion completes. However, this will not affect the data (MSB or LSB)
that is being shifted out. On the next read of the temperature register, the new
temperature value will be shifted out.
7.5 Power-up default condition
After power-on, the SE97B is initialized to the following default condition:
" Starts monitoring local sensor
" EVENT
register is cleared; EVENT
output is pulled HIGH by external pull-ups
" EVENT
hysteresis is defaulted to 0 癈
" Command pointer is defaulted to 00h
" Critical Temp, Alarm Temperature Upper and Lower Boundary Trip register are
defaulted to 0 癈
" Capability register is defaulted to 00F7h for the B-grade and VHV capability,
EVENT
de-asserted and SMBus TIMEOUT between 25 ms and 35 ms enabled.
" Operational mode: comparator
" SMBus register is defaulted to 21h
7.6 Device initialization
SE97B temperature sensors have programmable registers, which, upon power-up, default
to zero. The open-drain EVENT
output is default to being disabled, comparator mode and
active LOW. The alarm trigger registers default to being unprotected. The configuration
registers, upper and lower alarm boundary registers and critical temperature window are
defaulted to zero and need to be programmed to the desired values. SMBus TIMEOUT
feature defaults to being enabled and can be programmed to disable. These registers are
required to be initialized before the device can properly function. Except for the SPD,
which does not have any programmable registers, and does not need to be initialized.
相關PDF資料 |
PDF描述 |
|---|---|
| SE98ATP,547 | IC TEMP SENSOR DDR 8-HWSON |
| SG6901ASZ | IC PFC CTLR AVERAGE CURR 20SOIC |
| SG6932SZ | IC PFC CONTROLLER CCM 16SOP |
| SG6961SY | IC PFC CTRLR AVERAGE CURR 8SOIC |
| SI3500-A-GM | IC POE SWITCH PWR OVER LAN 20QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SE97PW | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:DDR memory module temp sensor with integrated SPD, 3.3 V |
| SE97PW,118 | 功能描述:板上安裝溫度傳感器 I2C LOCAL +/- 2OC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| SE97PW-T | 功能描述:板上安裝溫度傳感器 I2C LOCAL +/- 2OC TS +SPD DIMM RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| SE97TK | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:DDR memory module temp sensor with integrated SPD, 3.3 V |
| SE97TK,118 | 功能描述:板上安裝溫度傳感器 I2C LOCAL +/- 2OC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。