- 您現在的位置：買賣IC網 > PDF目錄98078 > SC18IS600IBS,151 (NXP SEMICONDUCTORS) I2C BUS CONTROLLER, PQCC24 PDF資料下載
參數資料
| 型號： | SC18IS600IBS,151 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 總線控制器 |
| 英文描述： | I2C BUS CONTROLLER, PQCC24 |
| 封裝： | 4 X 4 MM, 0.85 MM HEIGHT, PLASTIC, MO-220, SOT616-3, HVQFN-24 |
| 文件頁數： | 6/30頁 |
| 文件大?。?/td> | 164K |
| 代理商： | SC18IS600IBS,151 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
SC18IS600_601_5
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 05 — 28 July 2008
14 of 30
NXP Semiconductors
SC18IS600/601
SPI to I2C-bus interface
6.6.2 Read N bytes from I2C-bus slave device
Once the host issues this command, the SC18IS600/601 will start an I2C-bus read
transaction on the I2C-bus to the specied slave address. Once the data is received, the
SC18IS600/601 will place this data in the receiver buffer, and will generate an interrupt on
the INT pin. The ‘transaction completed’ status can be read in the I2CStat. Note that the
data is not returned until a Read Buffer command is performed (see Section 6.6.4 “Read
Note that the third byte sent by the host is the device slave address. The SC18IS600/601
will ignore the least signicant bit so a read will always be performed even if the least
signicant bit is a ‘0’. The maximum number of bytes to be read is 96.
6.6.3 I2C-bus read after write
Once the host issues this command, the SC18IS600/601 will start a write transaction on
the I2C-bus to the specied slave address. Once the data is written, the SC18IS600/601
will read data from the specied slave, place the data in the Receiver Buffer and generate
an interrupt on the INT pin. The ‘transaction completed’ status can be read in I2CStat.
Note that the data is not returned until a ‘Read Buffer’ command is performed.
6.6.4 Read buffer
Fig 14. Read N bytes from I2C-bus slave device
NUMBER
OF BYTES
0x01
COMMAND
SLAVE ADDRESS
+ R
SPI host sends
CS
SCLK
MOSI
1
slave address A[7:1]
number of bytes D[7:0]
command 0x01
002aab719
Fig 15. I2C-bus read after write
002aab720
NUMBER OF
WRITE
BYTES
0x02
COMMAND
SLAVE
ADDRESS
+ W
SPI host sends
DATA
WRITE
BYTE 0
DATA
WRITE
BYTE N
NUMBER OF
READ
BYTES
SLAVE
ADDRESS
+ R
Fig 16. Read buffer
002aab868
0x06
COMMAND
SPI host sends
DATA
BYTE 1
DATA
BYTE N
相關PDF資料 |
PDF描述 |
|---|---|
| SC18IS600IBS | I2C BUS CONTROLLER, PQCC24 |
| SC2200UCL-300 | 32-BIT, 300 MHz, MICROPROCESSOR, PBGA432 |
| SC2200UCL-300F | 32-BIT, 300 MHz, MICROPROCESSOR, PBGA432 |
| SC26C562A8A | 2 CHANNEL(S), 10M bps, MULTI PROTOCOL CONTROLLER, PQCC52 |
| SC26C92AA1A44 | 2 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PQCC44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC18IS600IPW | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:SPI to IC-bus interface |
| SC18IS600IPW,112 | 功能描述:總線收發器 INTERFACE SPI/I2C RoHS:否 制造商:Fairchild Semiconductor 邏輯類型:CMOS 邏輯系列:74VCX 每芯片的通道數量:16 輸入電平:CMOS 輸出電平:CMOS 輸出類型:3-State 高電平輸出電流:- 24 mA 低電平輸出電流:24 mA 傳播延遲時間:6.2 ns 電源電壓-最大:2.7 V, 3.6 V 電源電壓-最小:1.65 V, 2.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-48 封裝:Reel |
| SC18IS600IPW,128 | 功能描述:總線收發器 SPI-I2C MSTER BRIDGE RoHS:否 制造商:Fairchild Semiconductor 邏輯類型:CMOS 邏輯系列:74VCX 每芯片的通道數量:16 輸入電平:CMOS 輸出電平:CMOS 輸出類型:3-State 高電平輸出電流:- 24 mA 低電平輸出電流:24 mA 傳播延遲時間:6.2 ns 電源電壓-最大:2.7 V, 3.6 V 電源電壓-最小:1.65 V, 2.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-48 封裝:Reel |
| SC18IS600IPW/S8HP | 功能描述:SC18IS600I 制造商:nxp usa inc. 系列:- 包裝:剪切帶（CT） 零件狀態:在售 協議:I2C 功能:控制器 接口:SPI 標準:- 電壓 - 電源:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商器件封裝:16-TSSOP 標準包裝:1 |
| SC18IS600IPW112 | 制造商:Rochester Electronics LLC 功能描述: 制造商:NXP 功能描述: 制造商:NXP Semiconductors 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。