參數資料
型號： S29GL256N10FAI010
廠商： SPANSION LLC
元件分類： PROM
英文描述： MirrorBit Flash Family
中文描述： 16M X 16 FLASH 3V PROM, 100 ns, PBGA64
封裝： 13 X 11 MM, FBGA-64
文件頁數： 61/95頁
文件大?。?/td> 3781K
代理商： S29GL256N10FAI010
64
S29GL-N
S29GL-N_00_B8 May 30, 2008
Da ta
Sh e e t
10. Write Operation Status
The device provides several bits to determine the status of a program or erase operation: DQ2, DQ3, DQ5,
DQ6, and DQ7. Table 10.1 on page 68 and the following subsections describe the function of these bits. DQ7
and DQ6 each offer a method for determining whether a program or erase operation is complete or in
progress. The device also provides a hardware-based output signal, RY/BY#, to determine whether an
Embedded Program or Erase operation is in progress or is completed.
10.1
DQ7: Data# Polling
The Data# Polling bit, DQ7, indicates to the host system whether an Embedded Program or Erase algorithm
is in progress or completed, or whether the device is in Erase Suspend. Data# Polling is valid after the rising
edge of the final WE# pulse in the command sequence.
During the Embedded Program algorithm, the device outputs on DQ7 the complement of the datum
programmed to DQ7. This DQ7 status also applies to programming during Erase Suspend. When the
Embedded Program algorithm is complete, the device outputs the datum programmed to DQ7. The system
must provide the program address to read valid status information on DQ7. If a program address falls within a
protected sector, Data# Polling on DQ7 is active for approximately 1 s, then the device returns to the read
mode.
During the Embedded Erase algorithm, Data# Polling produces a 0 on DQ7. When the Embedded Erase
algorithm is complete, or if the device enters the Erase Suspend mode, Data# Polling produces a 1 on DQ7.
The system must provide an address within any of the sectors selected for erasure to read valid status
information on DQ7.
After an erase command sequence is written, if all sectors selected for erasing are protected, Data# Polling
on DQ7 is active for approximately 100 s, then the device returns to the read mode. If not all selected
sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the
selected sectors that are protected. However, if the system reads DQ7 at an address within a protected
sector, the status may not be valid.
Just prior to the completion of an Embedded Program or Erase operation, DQ7 may change asynchronously
with DQ0–DQ6 while Output Enable (OE#) is asserted low. That is, the device may change from providing
status information to valid data on DQ7. Depending on when the system samples the DQ7 output, it may read
the status or valid data. Even if the device has completed the program or erase operation and DQ7 has valid
data, the data outputs on DQ0–DQ6 may be still invalid. Valid data on DQ0–DQ7 appears on successive read
cycles.
Table 10.1 on page 68 shows the outputs for Data# Polling on DQ7. Figure 10.1 on page 65 shows the Data#
Polling algorithm. Figure 15.4 on page 76 shows the Data# Polling timing diagram.
相關PDF資料
PDF描述
S29GL256N10FFI010 MirrorBit Flash Family
S29GL256N80FAI010 MirrorBit Flash Family
S29GL256N80FFI010 MirrorBit Flash Family
S29GL256N80FFI013 MirrorBit Flash Family
S29JL032H90TAI223 2M X 16 FLASH 3V PROM, 90 ns, PDSO48
相關代理商/技術參數
參數描述
S29GL256N10FAI020 制造商:Spansion 功能描述:
S29GL256N10FFI010 制造商:Spansion 功能描述:NOR Flash Parallel 3V/3.3V 256Mbit 32M/16M x 8bit/16bit 100ns 64-Pin Fortified BGA Tray 制造商:Spansion 功能描述:MIRRORBIT FLASH 256MB SMD 29LV256
S29GL256N10FFI012 制造商:Spansion 功能描述:Flash - NOR IC
S29GL256N10FFI020 制造商:Spansion 功能描述:NOR Flash Parallel 3V/3.3V 256Mbit 32M/16M x 8bit/16bit 100ns 64-Pin Fortified BGA Tray 制造商:Spansion 功能描述:MIRRORBIT FLASH 256MB SMD 29LV256
S29GL256N10TFI010 功能描述:IC FLASH 制造商:cypress semiconductor corp 系列:GL-N 包裝:托盤 零件狀態:在售 存儲器類型:非易失 存儲器格式:閃存 技術:FLASH - NOR 存儲容量:256Mb （32M x 8，16M x 16） 寫周期時間 - 字，頁:100ns 訪問時間:100ns 存儲器接口:并聯 電壓 - 電源:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:56-TFSOP（0.724"，18.40mm 寬） 供應商器件封裝:56-TSOP 標準包裝:91
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*