- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C63466F 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PQFP144 PDF資料下載
參數資料
| 型號： | S1C63466F |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PQFP144 |
| 封裝： | PLASTIC, QFP8-144 |
| 文件頁數： | 93/135頁 |
| 文件大?。?/td> | 1053K |
| 代理商： | S1C63466F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁當前第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁
52
EPSON
S1C63466 TECHNICAL MANUAL
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (LCD Driver)
When a bit in the display memory is set to "1", the corresponding LCD dot goes ON, and when it is set to
"0", the dot goes OFF.
At 1/17 (1/16) duty drive, all data of COM0–COM16 (15) is output.
At 1/8 duty drive, data only corresponding to COM0–COM7 is output. However, since the display
memory has capacity for two screens, it is designed so that the memory for COM8–COM15 shown in
Figure 4.7.5.1 (b) can also be used as COM0–COM7. Select either F000H–F077H or F100H–F177H for the
area to be displayed (to be output from COM0–COM7 terminals) using the LPAGE register. It can switch
the screen in an instant.
At initial reset, the data memory content becomes undefined hence, there is need to initialize using the
software.
The display memory has read/write capability, and the addresses that have not been used for LCD
display can be used as general purpose registers.
Note: When a program that access no memory mounted area (F078H–F0FFH, F178H–F1FFH, F201H,
F203H, , F277H) is made, the operation is not guaranteed.
4.7.6 LCD contrast adjustment
In the S1C63466, the LCD contrast can be adjusted by the software.
It is realized by controlling the voltages VC1, VC2, VC4 and VC5 output from the LCD system voltage
circuit. When these voltages are supplied to the externally expanded LCD driver, the expanded LCD
contrast is adjusted at the same time. However, when the LCD drive voltage is supplied from outside by
the mask option selection, this adjustment becomes invalid.
The contrast can be adjusted to 16 levels as shown in Table 4.7.6.1. When VCCHG = "0", VC1 is changed
within the range from 0.975 V to 1.2 V, and other voltages change according to VC1. When VCCHG = "1",
VC2 is changed within the range from 1.950 V to 2.4 V, and other voltages change according to VC2.
Table 4.7.6.1 LCD contrast
No.
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
LC3
0
1
LC2
0
1
0
1
LC1
0
1
0
1
0
1
0
1
LC0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Contrast
light
dark
At room temperature, use setting number 7 or 8 as standard.
Since the contents of LC0–LC3 are undefined at initial reset, initialize it by the software.
相關PDF資料 |
PDF描述 |
|---|---|
| S1C63567F0A0100 | MICROCONTROLLER, PQFP144 |
| S1C63653F | 4-BIT, FLASH, 4 MHz, MICROCONTROLLER, CQFP100 |
| S1C6F567D0A0100 | MICROCONTROLLER, UUC141 |
| S1C6N3B0D0A0100 | MICROCONTROLLER, UUC54 |
| S1C6P366D0A0100 | 4-BIT, FLASH, 4.1 MHz, MICROCONTROLLER, UUC102 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C63557D04Q000 | 制造商:Seiko Instruments Inc (SII) 功能描述:EPSON MCU 4BIT |
| S1C63567 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63616 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63632 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63653 | 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。