參數資料
型號： S1C63455D
元件分類： 微控制器/微處理器
英文描述： 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, UUC105
封裝： DIE-105
文件頁數： 99/119頁
文件大?。?/td> 865K
代理商： S1C63455D
72
EPSON
S1C63455 TECHNICAL MANUAL
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Serial Interface)
SDP: Data input/output permutation selection register (FF71HD3)
Selects the serial data input/output permutation.
When "1" is written: MSB first
When "0" is written: LSB first
Reading: Valid
Select whether the data input/output permutation will be MSB first or LSB first.
At initial reset, this register is set to "0".
SCTRG: Clock trigger/status (FF70HD1)
This is a trigger to start input/output of synchronous clock (SCLK).
When writing
When "1" is written: Trigger
When "0" is written: No operation
When this trigger is supplied to the serial interface activating circuit, the synchronous clock (SCLK)
input/output is started.
As a trigger condition, it is required that data writing or reading on data registers SD0–SD7 be performed
prior to writing "1" to SCTRG. (The internal circuit of the serial interface is initiated through data writ-
ing/reading on data registers SD0–SD7.) In addition, be sure to enable the serial interface with the ESIF
register before setting the trigger.
Supply trigger only once every time the serial interface is placed in the RUN state. Refrain from perform-
ing trigger input multiple times, as leads to malfunctioning.
Moreover, when the synchronous clock SCLK is external clock, start to input the external clock after the
trigger.
When reading
When "1" is read: RUN (during input/output the synchronous clock)
When "0" is read: STOP (the synchronous clock stops)
Writing: Invalid
When this bit is read, it indicates the status of serial interface clock.
After "1" is written to SCTRG, this value is latched till serial interface clock stops (8 clock counts). There-
fore, if "1" is read, it indicates that the synchronous clock is in input/output operation.
When the synchronous clock input/output is completed, this latch is reset to "0".
At initial reset, this bit is set to "0".
SD0–SD3, SD4–SD7: Serial interface data register (FF72H, FF73H)
These registers are used for writing and reading serial data.
When writing
When "1" is written: High level
When "0" is written: Low level
Write data to be output in these registers. The register data is converted into serial data and output from
the SOUT (P11) terminal; data bits set at "1" are output as high (VDD) level and data bits set at "0" are
output as low (VSS) level.
When reading
When "1" is read: High level
When "0" is read: Low level
The serial data input from the SIN (P10) terminal can be read from these registers.
The serial data input from the SIN (P10) terminal is converted into parallel data, as a high (VDD) level bit
into "1" and as a low (VSS) level bit into "0", and is loaded to these registers. Perform data reading only
while the serial interface is not running (i.e., the synchronous clock is neither being input or output).
At initial reset, these registers are undefined.
相關PDF資料
PDF描述
S1C63458F0A0100 MICROCONTROLLER, PQFP144
S1C63466D 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, UUC140
S1C63466F 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PQFP144
S1C63567F0A0100 MICROCONTROLLER, PQFP144
S1C63653F 4-BIT, FLASH, 4 MHz, MICROCONTROLLER, CQFP100
相關代理商/技術參數
參數描述
S1C63557D04Q000 制造商:Seiko Instruments Inc (SII) 功能描述:EPSON MCU 4BIT
S1C63567 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63616 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63632 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63653 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*