參數資料
型號： PCD5013H
廠商： NXP SEMICONDUCTORS
元件分類： 尋呼電路
英文描述： FLEX roaming decoder II
中文描述： TELECOM, PAGING DECODER, PQFP32
封裝： 7 X 7 MM, 1.40 MM HEIGHT, PLASTIC, SOT-358-1, LQFP-32
文件頁數： 40/76頁
文件大?。?/td> 270K
代理商： PCD5013H
1999 Apr 12
40
Philips Semiconductors
Product specification
FLEX
roaming decoder II
PCD5013
Table 38
Frame assignment packet bit assignments
BYTE
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
3
2
1
0
0
0
0
0
1
0
0
0
0
0
f
2
0
f
1
0
f
0
0
AF
15
AF
7
AF
14
AF
6
AF
13
AF
5
AF
12
AF
4
AF
11
AF
3
AF
10
AF
2
AF
9
AF
1
AF
8
AF
0
8.7
Call data packets
8.7.1
G
ENERAL
The PCD5013 sends data extracted from the
FLEX
signal to the host in SPI packets using the
following packet types:
BIW packets which contain data transmitted in BIWs
Address packets which indicate that a call has been
detected and give additional information about call
attributes
Vector packets which indicate the call type and indicate
which message word numbers (WN) are associated
with the call
Message packets which contain the information
contained within the message codewords of a call.
For more information about the function of these packets
within the FLEX
data stream see Section 8.8.
8.7.2
A
DDRESS PACKET
(ID = 01H)
Information from address codewords in received calls is
sent to the host in address packets. If less than 3-bit errors
are detected in a received address word and it matches an
enabled address assigned to the PCD5013, the address
packet is sent to the host processor. The address packet
contains the call address, the location in the data stream
of the associated vector, and other miscellaneous call
data.
PA:
priority address (Table 39). This bit is set if the
address was received as a priority address.
p:
phase (Table 39). This is the phase on which the
address was detected (0 = A, 1 = B, 2 = C and 3 = D).
LA:
long address (Table 39). This bit is set if the address
was programmed in the PCD5013 as a LA.
AI:
address index (Table 39). This index identifies which
address was detected. Valid values are 00H to 0FH,
corresponding to the 16 programmable address words
and 80H to 8FH, corresponding to the 16 temporary
addresses (Section 8.8.5). Values 144 through to 159
correspond to 16 operator messaging addresses.
For long addresses, the address packet is only sent once
with AI referring to the second word of the address.
TOA:
tone-only address (Table 39). This bit is set if the
address was programmed as a tone-only address.
No vector word is sent for tone-only addresses. This bit is
never set for temporary or operator messaging addresses.
WN:
word number of vector (2 to 87 decimal) (Table 39).
The location of the vector within this frame for the detected
address. This value is invalid for this packet if the TOA bit
is set.
x:
unused bits (Table 39). The value of these bits is not
guaranteed.
8.7.3
V
ECTOR PACKETS
(ID = 02H
TO
57H)
Information from vector codewords in received calls is sent
to the host in vector packets. For any address packet sent
to the host (except tone-only addresses), a corresponding
vector packet is always sent.
The ID of the vector packet is the word number where the
vector word was received in the frame. The host must
associate vector packets with a call by searching for an
address packet previously received on the same phase
and with WN bits which match the ID of the vector packet.
The vector type of a vector packet indicates the format of
a call as one of:
Numeric (3 types)
Short message/tone-only
Hex/binary
Alphanumeric
Secure message
Short instruction.
The numeric, hex/binary, alphanumeric, and secure
message vector packets indicate the location and number
of message word packets in the message field. If more
than two bit errors are detected in the vector word (via
BCH calculations, parity calculations, check character
calculations, or value validation) the e bit is set and the
message words are not sent.
相關PDF資料
PDF描述
PCD5032 ADPCM CODEC for digital cordless telephones
PCD5032H ADPCM CODEC for digital cordless telephones
PCD5032T ADPCM CODEC for digital cordless telephones
PCD5041 DECT burst mode controller
PCD5041H DECT burst mode controller
相關代理商/技術參數
參數描述
PCD5032 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ADPCM CODEC for digital cordless telephones
PCD5032B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Linear CODEC
PCD5032D 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Linear CODEC
PCD5032H 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ADPCM CODEC for digital cordless telephones
PCD5032T 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ADPCM CODEC for digital cordless telephones
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*