- 您現在的位置：買賣IC網 > PDF目錄382380 > PCD5013H (NXP SEMICONDUCTORS) FLEX roaming decoder II PDF資料下載
參數資料
| 型號： | PCD5013H |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 尋呼電路 |
| 英文描述： | FLEX roaming decoder II |
| 中文描述： | TELECOM, PAGING DECODER, PQFP32 |
| 封裝： | 7 X 7 MM, 1.40 MM HEIGHT, PLASTIC, SOT-358-1, LQFP-32 |
| 文件頁數： | 15/76頁 |
| 文件大?。?/td> | 270K |
| 代理商： | PCD5013H |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
1999 Apr 12
15
Philips Semiconductors
Product specification
FLEX
roaming decoder II
PCD5013
8.4
Configuration and synchronisation
8.4.1
G
ENERAL
After a reset, all configuration data has to be (re)loaded
into the PCD5013 by the host using the SPI. PCD5013
features which do not change during operation are
configured using the configuration packet (Section 8.4.4),
the receiver control packets (Section 8.5) and the address
configuration packets (Section 8.6). PCD5013 features
which can be changed during operation are configured
using the control packet. The checksum packet ensures
proper communication between the host and the
PCD5013.
8.4.2
SPI
SECURITY ALGORITHM
The PCD5013 provides a security algorithm to verify
correct SPI operation (Figs 9 and 10). The PCD5013
maintains a checksum register equal to the result of
XORing the 24 data bits of every packet it receives, except
the checksum packet 00H and special packets
1CH to 1FH. When the PCD5013 is reset, the internal
checksum register is initialized to the 24-bit part ID defined
in the part ID packet.
Immediately following a reset and whenever the host
sends a packet other than a checksum packet, the
SPI output of status and data (SPI transmit) is disabled.
The PCD5013 then initiates SPI transfers continuously,
sending the part ID packet (Section 8.4.5). Note that when
SPI transmit is disabled all decoding and timing functions
are unaffected. The SPI transmit can be enabled by
sending a checksum packet for which the checksum value
matches the checksum register.
Checksum packets sent when the SPI transmit is enabled,
are ignored by the PCD5013 irrespective of the value of
the checksum packet data bits. Thus when the PCD5013
initiates an SPI transfer and the host has no data to send,
the host should send the checksum packet so as not to
disable the SPI transmit. The data in the checksum packet
could be a null packet (32-bit stream of all zeros).
Sending a packet other than the checksum packet when
the SPI transmit is enabled causes the SPI transmit to be
disabled until a checksum packet is sent with the correct
value. Thus when the host re-configures the PCD5013
after a reset, the SPI transmit is disabled until the host
sends a checksum packet at the end of the configuration
data, with the checksum value equal to the result of
XORing together the data bits of each of the configuring
packets and the data bits of the part ID packet.
If the SPI transmit is enabled and a receiver shutdown
packet is pending, the receiver shutdown packet is sent. If
there is no receiver shutdown packet pending, but there is
a roaming status packet pending, the roaming status
packet is sent. If neither the receiver shutdown packet nor
the roaming status packet is pending and there is data in
the transmit buffer, the PCD5013 initiates an SPI transfer
sending a packet from its transmit buffer. The PCD5013
sends the status packet (which is not buffered) when the
host initiates an SPI transfer and the transmit buffer is
empty.
Fig.9 SPI transmit functional block diagram.
handbook, full pagewidth
MGR618
ROAMING STATUS REGISTER
STATUS REGISTER
SPI
SECURITY
ALGORITHM
MUX
SPI TRANSMIT REGISTER
MISO
32
×
32 DATA PACKET
FIFO TRANSMIT
BUFFER
32
RECEIVER SHUTDOWN REGISTER
32
PART ID REGISTER
32
32
32
32
相關PDF資料 |
PDF描述 |
|---|---|
| PCD5032 | ADPCM CODEC for digital cordless telephones |
| PCD5032H | ADPCM CODEC for digital cordless telephones |
| PCD5032T | ADPCM CODEC for digital cordless telephones |
| PCD5041 | DECT burst mode controller |
| PCD5041H | DECT burst mode controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCD5032 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ADPCM CODEC for digital cordless telephones |
| PCD5032B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Linear CODEC |
| PCD5032D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Linear CODEC |
| PCD5032H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ADPCM CODEC for digital cordless telephones |
| PCD5032T | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ADPCM CODEC for digital cordless telephones |
發布緊急采購，3分鐘左右您將得到回復。