參數資料
型號： PCD5013
廠商： NXP Semiconductors N.V.
英文描述： FLEX roaming decoder II
中文描述： FleX創建漫游解碼器二
文件頁數： 39/76頁
文件大?。?/td> 270K
代理商： PCD5013
1999 Apr 12
39
Philips Semiconductors
Product specification
FLEX
roaming decoder II
PCD5013
8.6.7
C
ONFIGURATION OF ASSIGNED FRAMES AND PAGER
COLLAPSE
(ID = 20H
TO
27H)
The assigned frame and collapse value determine the
frames in which the decoding device typically looks for
messages (other system factors can cause the decoding
device to look in other frames in addition to the typical
frames).
The PCD5013 must be configured explicitly to receive all
required frames by setting the associated assigned
frame (AF) bits. For each enabled CAPCODE these are
the base frame and the associated frames implied by the
pager collapse value. For example if the PCD5013 has
one enabled address and it is assigned to base frame 3
with a collapse value of 4, the AF bits for
frames 3, 19, 35, 51, 67, 83, 99 and 115 should be set
and the AF bits for all other frames should be cleared.
When the PCD5013 is configured for manual collapse
mode by setting the MCM bit in the Roaming Control
Packet, the PCD5013 does not apply the received system
collapse to the AF bits. The host should set the AF bits for
all frames that should be decoded on all channels.
For example, if frames 0 and 64 should be decoded on one
channel and frames 4, 36, 68, and 100 should be decoded
on another channel, all six of the corresponding AF bits
should be set. The host can then change the receiver’s
carrier frequency after the PCD5013 decodes frames 0,
36, 64, and 100.
There are 8 frame assignment packets each capable of
assigning a range of 16 consecutive frame numbers.
f:
frame range, see Table 38 for location in the frame
assignment packet and Table 36 for the AFs and values.
The value determines which 16 frames out of a range
of 128 correspond to the 16 AF bits in the packet. At least
one of these bits must have been set when the PCD5013
is turned on by setting the ON bit in the control packet.
Value after reset = 0.
AF:
assigned frame (Table 38). If a bit is set, the PCD5013
decodes the associated FLEX
frame and scans its
contents for enabled addresses. Value after reset = 0.
8.6.8
C
ONFIGURATION OF ASSIGNED PHASE
The assigned phase is required only for single-phase
devices. It determines the phase (A, B, C, or D) in which
the messages are received.
For details of phase calculation see Section 8.6.5.
For details of programming the assigned phase
see Section 8.4.7.
Table 36
Frame assignment ranges
8.6.9
O
PERATOR
M
ESSAGING
A
DDRESS
E
NABLE
P
ACKET
(ID = 04H)
The operator messaging address enable packet is used to
enable and disable the built-in FLEX
operator messaging
addresses. Enabling and disabling operator messaging
addresses does not affect on which frames the decoder IC
decodes. To ensure that the correct frames are decoded,
the host must modify the FF bits in the Control Packet or
the AF bits in the Frame Assignment Packets.
OAE:
operator messaging address enable (Table 37).
When a bit is set, the corresponding operator messaging
address is enabled. When it is cleared, the corresponding
operator messaging address is disabled. OAE
0
to OAE
15
corresponds to the hexadecimal operator messaging
address values of 1F7810 through to 1F781F
respectively. Value after reset = 0.
f
2
0
0
0
0
1
1
1
1
f
1
0
0
1
1
0
0
1
1
f
0
0
1
0
1
0
1
0
1
AF
15
AF
0
frame 127
frame 111
frame 95
frame 79
frame 63
frame 47
frame 31
frame 15
frame 112
frame 96
frame 80
frame 64
frame 48
frame 32
frame 16
frame 0
Table 37
Operator messaging address enable packet bit assignments
BYTE
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
3
2
1
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
OAE
15
OAE
7
OAE
14
OAE
6
OAE
13
OAE
5
OAE
12
OAE
4
OAE
11
OAE
3
OAE
10
OAE
2
OAE
9
OAE
1
OAE
8
OAE
0
相關PDF資料
PDF描述
PCD5013H FLEX roaming decoder II
PCD5032 ADPCM CODEC for digital cordless telephones
PCD5032H ADPCM CODEC for digital cordless telephones
PCD5032T ADPCM CODEC for digital cordless telephones
PCD5041 DECT burst mode controller
相關代理商/技術參數
參數描述
PCD5013H 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:FLEX roaming decoder II
PCD5032 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ADPCM CODEC for digital cordless telephones
PCD5032B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Linear CODEC
PCD5032D 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Linear CODEC
PCD5032H 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ADPCM CODEC for digital cordless telephones
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*