- 您現在的位置：買賣IC網 > PDF目錄382380 > PCD5013 (NXP Semiconductors N.V.) FLEX roaming decoder II PDF資料下載
參數資料
| 型號： | PCD5013 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | FLEX roaming decoder II |
| 中文描述： | FleX創(chuàng)建漫游解碼器二 |
| 文件頁數： | 33/76頁 |
| 文件大?。?/td> | 270K |
| 代理商： | PCD5013 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
1999 Apr 12
33
Philips Semiconductors
Product specification
FLEX
roaming decoder II
PCD5013
8.5.8
R
ECEIVER SHUT
-
DOWN SEQUENCE
The PCD5013 allows up to 3 steps associated with
shutting down the receiver. When the PCD5013 decides to
turn off the receiver, the first shut-down setting, if enabled,
is applied to the receiver control lines for the
corresponding shut-down time. At the end of the last used
shut-down time, the receiver off setting is applied to the
receiver control lines. If the first shut-down setting is not
enabled, the PCD5013 switches directly from the
receiver on to the receiver off setting.
Figure 15 shows the receiver shut-down sequence when
all shut-down settings are enabled. If the receiver is on or
being warmed up when the decoder is turned off (by
clearing the ON bit in the control packet), the PCD5013
immediately executes the receiver shut-down sequence.
If the PCD5013 is executing the shut-down sequence
when turned on (with the ON bit in the control packet set)
the PCD5013 completes the shut-down sequence before
starting the warm-up sequence.
8.5.8.1
Receiver shut-down setting packets
(ID = 1AH to 1BH)
SE:
step enable (Table 28). The receiver setting is
enabled when the bit is set. If the bit is cleared then that
step in the receiver shut-down sequence is disabled and
all following steps are ignored. Value after reset = 0.
LBC:
low battery check (Table 28). If this bit is set, the
PCD5013 checks the status of the LOBAT port just before
leaving this receiver shut-down state. Value after
reset = 0.
CLS:
control line setting (Table 28). This is the value to be
output on the receiver control lines (S0 to S7) for this
receiver shut-down state. Value after reset = 0.
ST:
step time (Table 28). This sets the duration time for
receiver shut-down, until the next receiver state.
The setting is in steps of 625
μ
s. Valid values are
625
μ
s (ST = 01H) to 39.375 ms (ST = 3FH). Value after
reset = 01H.
s:
setting number, see Tables 27 and 28 for the s names
and values and location in the receiver shut-down packet.
Table 27
s names and values
s
SETTING NAME
0
1
shut-down 1
shut-down 2
Table 28
Receiver shut-down stages
BYTE
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
3
2
1
0
0
0
0
0
0
1
0
1
0
0
1
0
s
0
SE
CLS
7
0
LBC
CLS
3
ST
3
CLS
6
0
CLS
5
ST
5
CLS
4
ST
4
CLS
2
ST
2
CLS
1
ST
1
CLS
0
ST
0
Fig.15 Receiver shut-down sequence.
handbook, full pagewidth
MGK267
receiver
control
line setting
shut down
time 1
shut down
setting 1
shut down
time 2
shut down
setting 2
possible
LOBAT
check
off
possible
LOBAT
check
possible
LOBAT
check
1600 sps or 3200 sps
sync or data setting
相關PDF資料 |
PDF描述 |
|---|---|
| PCD5013H | FLEX roaming decoder II |
| PCD5032 | ADPCM CODEC for digital cordless telephones |
| PCD5032H | ADPCM CODEC for digital cordless telephones |
| PCD5032T | ADPCM CODEC for digital cordless telephones |
| PCD5041 | DECT burst mode controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCD5013H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:FLEX roaming decoder II |
| PCD5032 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ADPCM CODEC for digital cordless telephones |
| PCD5032B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Linear CODEC |
| PCD5032D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Linear CODEC |
| PCD5032H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ADPCM CODEC for digital cordless telephones |
發(fā)布緊急采購，3分鐘左右您將得到回復。