- 您現在的位置：買賣IC網 > PDF目錄367801 > PC8240VTPU200ETC (Atmel Corp.) Integrated Processor Family PDF資料下載
參數資料
| 型號： | PC8240VTPU200ETC |
| 廠商： | Atmel Corp. |
| 英文描述： | Integrated Processor Family |
| 中文描述： | 綜合處理器系列 |
| 文件頁數： | 37/42頁 |
| 文件大小： | 421K |
| 代理商： | PC8240VTPU200ETC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁
37
PC8240
2149A–HIREL–05/02
The SDRAM_SYNC_OUT signal is intended to be routed halfway out to the SDRAM
devices and then returned to the SDRAM_SYNC_IN input of the PC8240. The trace
length may be used to skew or adjust the timing window as needed. See Motorola appli-
cation note AN1794/D for more information on this topic.
Pull-up/Pull-down Resistor
Requirements
The data bus input receivers are normally turned off when no read operation is in
progress; therefore, they do not require pull-up resistors on the bus. The data bus sig-
nals are: DH[0
–
31], DL[0 – 31], and PAR[0 – 7].
If the 32-bit data bus mode is selected, the input receivers of the unused data and parity
bits (DL[0 – 31], and PAR[4 – 7]) will be disabled, and their outputs will drive logic zeros
when they would otherwise normally be driven. For this mode, these pins do not require
pull-up resistors, and should be left unconnected by the system to minimize possible
output switching.
The TEST[0 – 1] pins require pull-up resistors of 120
or less connected to OVdd.
It is recommended that TEST2 have weak pull-up resistor (2
k
– 10 k
) connected to
GVdd.
It is recommended that the following signals be pulled up to OVdd with weak pull-up
resistors (2 k
– 10 k
): SDA, SCL, SMI, SRESET, TBEN, CHKSTOP_IN, TEST3, and
TEST4.
It is recommended that the following PCI control signals be pulled up to LVdd with weak
pull-up resistors (2 k
– 10 k
): DEVSEL, FRAME, IRDY, LOCK, PERR, SERR, STOP,
and TRDY. The resistor values may need to be adjusted stronger to reduce induced
noise on specific board designs.
The following pins have internal pull-up resistors enabled at all times: REQ[0 – 3],
REQ4/DA4, TCK, TDI, TMS, and TRST. See Table 1, “PC8240 Pinout Listing,” on
page 3 for more information.
The following pins have internal pull-up resistors enabled only while device is in the
reset state: GNT4/DA5, DL0, FOE, RCS0, SDRAS, SDCAS, CKE, AS, MCP, MAA[0 –
2], PMAA[0 – 2]. See Table 1, “PC8240 Pinout Listing,” on page 3 for more information.
The following pins are reset configuration pins: GNT4/DA5, DL0, FOE, RCS0, CKE, AS,
MCP, QACK/DA0, MAA[0 – 2], PMAA[0 – 2], and PLL_CFG[0 – 4]/DA[10 – 6]. These
pins are sampled during reset to configure the device.
Reset configuration pins should be tied to GND via 1 k
pull-down resistors to ensure a
logic zero level is read into the configuration bits during reset if the default logic one
level is not desired.
Any other unused active low input pins should be tied to a logic one level via weak pull-
up resistors (2
k
– 10 k
) to the appropriate power supply listed in Table 3 on page 8.
Unused active high input pins should be tied to GND via weak pull-down resistors
(2
k
– 10 k
).
相關PDF資料 |
PDF描述 |
|---|---|
| PC8245 | Integrated Processor Family |
| PC8245MTPU300D | Integrated Processor Family |
| PC8245MTPU333D | Integrated Processor Family |
| PC824A | NPN-OUTPUT DC-INPUT OPTOCOUPLER |
| PC844A | NPN-OUTPUT AC-INPUT OPTOCOUPLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PC8245 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Integrated Processor Family |
| PC8245MTPU300D | 制造商:e2v Aerospace & Defense 功能描述:MPU MPC82xx RISC 32-Bit 0.25um 300MHz 3.3V 352-Pin TBGA 制造商:e2v technologies 功能描述:MPU MPC82XX RISC 32BIT 0.25UM 300MHZ 3.3V 352TBGA - Trays |
| PC8245MTPU333D | 制造商:e2v Aerospace & Defense 功能描述:MPU MPC82xx RISC 32-Bit 0.25um 333MHz 3.3V 352-Pin TBGA 制造商:e2v technologies 功能描述:MPU MPC82XX RISC 32BIT 0.25UM 333MHZ 3.3V 352TBGA - Trays |
| PC8245MTPU350D | 制造商:e2v technologies 功能描述:PC8245MTPU350D - Trays |
| PC824A | 功能描述:PHOTOCOUPLER 2CH AC INPUT 8-DIP RoHS:否 類別:隔離器 >> 光隔離器 - 晶體管，光電輸出 系列:- 標準包裝:1,000 系列:- 通道數:2 輸入類型:DC 電壓 - 隔離:2500Vrms 電流傳輸比（最小值）:7% @ 16mA 電流傳輸比（最大）:50% @ 16mA 輸出電壓:20V 電流 - 輸出 / 通道:8mA 電流 - DC 正向(If):25mA Vce飽和（最大）:- 輸出類型:有 Vcc 的晶體管 安裝類型:通孔 封裝/外殼:8-DIP（0.400"，10.16mm） 包裝:管件 其它名稱:HCPL-2530W |
發布緊急采購，3分鐘左右您將得到回復。