- 您現在的位置：買賣IC網 > PDF目錄383727 > OX16PCI954 (Electronic Theatre Controls, Inc.) Integrated Quad UART and PCI interface PDF資料下載
參數資料
| 型號： | OX16PCI954 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Integrated Quad UART and PCI interface |
| 中文描述： | 綜合四UART和PCI接口 |
| 文件頁數： | 49/72頁 |
| 文件大?。?/td> | 656K |
| 代理商： | OX16PCI954 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁當前第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
Data Sheet Revision 1.3
Page 49
OX16PCI954
OXFORD SEMICONDUCTOR LTD.
7.11.8 Clock Select Register ‘CKS’
The CKS register is located at offset 0x03 of the ICR
This register is cleared to 0x00 after a hardware reset to
maintain compatibility with 16C550, but is unaffected by
software reset. This allows the user to select a clock
source and then reset the channel to work-around any
timng glitches.
CKS[1:0]: Receiver Clock Source Selector
logic [x0]
The output of baud rate generator (internal
BDOUT#) is selected for the receiver clock.
logic [01]
The DSR#pin is selected for the receiver
clock.
logic [11]
The transmtter clock is selected for the
receiver. This allows RI#to be used for both
transmtter and receiver.
CKS[2]: Reserved
CKS[3]: Receiver 1x clock mode selector
logic 0
The receiver is in Nx clock mode as defined in
the TCR register. After a hardware reset the
receiver operates in 16x clock mode, i.e.
16C550 compatibility.
logic 1
The receiver is in isochronous 1x clock mode.
CKS[5:4]: Transmitter 1x clock or baud rate generator
output (BDOUT) on DTR#pin
logic [00]
The function of the DTR#pin is defined by
the setting of ACR[4:3].
logic [01]
The transmtter 1x clock (bit rate clock) is
asserted on the DTR#pin and the setting of
ACR[4:3] is ignored.
logic [10]
The output of baud rate generator (Nx clock)
is asserted on the DTR#pin and the setting
of ACR[4:3] is ignored.
logic [11]
Reserved.
CKS[6]: Transmitter clock source selector
logic 0
The transmtter clock source is the output of the
baud rate generator (550 compatibility).
logic 1
The transmtter uses an external clock applied
to the RI#pin.
CKS[7]: Transmitter 1x clock mode selector
logic 0
The transmtter is in Nx clock mode as defined
in the TCR register. After a hardware reset the
transmtter operates in 16x clock mode, i.e.
16C550 compatibility.
logic 1
The transmtter is in isochronous 1x clock
mode.
7.11.9 Nine-bit Mode Register ‘NMR’
The NMR register is located at offset 0x0D of the ICR
The UART offers 9-bit data framng for industrial multi-drop
applications. The 9-bit mode is enabled by setting bit 0 of
the Nine-bit Mode Register (NMR). In 9-bit mode the data
length setting in LCR[1:0] is ignored. Furthermore as parity
is permanently disabled, the setting of LCR[5:3] is also
ignored.
The receiver stores the 9th bit of the received data in
LSR[2] (where parity error is stored in normal mode). Note
that the UART provides a 128-deep FIFO for LSR[3:0].
The transmtter FIFO is 9 bits wide and 128 deep. The user
should write the 9th (MSB) data bit in SPR[0] first and then
write the other 8 bits to THR.
As parity mode is disabled, LSR[7] is set whenever there is
an overrun, framng error or received break condition. It is
unaffected by the contents of LSR[2] (Now the received 9th
data bit).
In 9-bit mode, in-band flow control is disabled regardless of
the setting of EFR[3:0] and the XON1/XON2/XOFF1 and
XOFF2 registers are used for special character detection.
Interrupts in 9-Bit Mode:
While IER[2] is set, upon receiving a character with status
error, a level 1 interrupt is asserted when the character and
the associated status are transferred to the FIFO.
The UART can assert an optional interrupt if a received
character has its 9
th
bit set. As multi-drop systems often
use the 9
th
bit as an address bit, the receiver is able to
generate an interrupt upon receiving an address character.
This feature is enabled by setting NMR[2]. This will result
in a level 1 interrupt being asserted when the address
character is transferred to the receiver FIFO.
In this case, as long as there are no errors pending, i.e.
LSR[1], LSR[3], and LSR[4] are clear, '0' can be read back
fromLSR[7] and LSR[1], thus differentiating between an
‘a(chǎn)ddress’ interrupt and receiver error or overrun interrupt in
9-bit mode. Note however that should an overrun or error
interrupt actually occur, an address character may also
reside in the FIFO. In this case, the software driver should
examne the contents of the receiver FIFO as well as
process the error.
相關PDF資料 |
PDF描述 |
|---|---|
| OX16PCI954-TQC60-A | Integrated Quad UART and PCI interface |
| OX4240 | OCXO |
| OX1040 | OCXO |
| OX1041 | OCXO |
| OX1042 | OCXO |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OX16PCI954_05 | 制造商:OXFORD 制造商全稱:OXFORD 功能描述:Integrated Quad UART and PCI interface |
| OX16PCI954-TQA1G | 功能描述:外圍驅動器與原件 - PCI PCI bridge to quad serial & para. port RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| OX16PCI954-TQC60-A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Integrated Quad UART and PCI interface |
| OX16PCI954-TQC60-A1 | 制造商:OXFORD 制造商全稱:OXFORD 功能描述:Integrated Quad UART and PCI interface |
| OX16PCI958 | 制造商:OXFORD 制造商全稱:OXFORD 功能描述:Octal UART with PCI Interface |
發布緊急采購，3分鐘左右您將得到回復。