
S INGLE IC CMOS  COLOR AND B/W DIGIT AL CAMERAS
March 4, 2000 
Version 1.0 
27 
resolution is 0.21%. Control byte is 10 bit. Every LSB equal decrease frame rate 
0.21%. Range is 0.21% - 109%. IF frame rate adjustment enable, COME[7] must set 
to “0”. 
Reserved 
Common control J 
COMJ[7:5] – reserved 
COMJ[4] – Enable auto black expanding mode. 
COMJ[3] – “1” update white balance update only if AGC/AEC is stable. “0” update 
white balance independent with AEC/AGC. 
COMJ[2] – Band filter enable. After adjust frame rate to match indoor light frequency, 
this bit enable a different exposure algorithm to cut light band induced by fluorescent 
light. 
COMJ[1] – reserved 
COMJ[0] –U and V offset separate mode. “1” U and V use separate offsets. “0” U and 
V use same offset defined by register [2E]. 
V channel offset adjustment 
VCOFF[7] – Offset adjustment direction: “0” = Add V[6:0]; “1” = Subtract V[6:0]. 
VCOFF[6:0] – V channel digital output offset adjustment. Range: +128 ~ -128. If 
COMG[2]=0, this register will be updated by internal circuit. Write to this register 
through I
2
C has no effect. If COMG[2] =1, V channel offset adjustment will use the 
stored value which can be changed through I
2
C. If COMF[1] =1, this register has no 
effect to digital output data. If output RGB raw data, this register will adjust R/G/B 
data. 
Note: 
This function is not available on the OV6130 image sensor. 
Reserved 
Color processing parameter control 
CPP[7:6] – reserved 
CPP[5] – Luminance gamma on/off. “1” - luminance gamma on; “0” - luminance 
gamma is 1. 
CPP[4:0] – reserved 
Bias adjustment 
BIAS[7:6] – A/D reference level adjustment. “00” - 110% internal full signal range; 
“01” - 120%, “10” - 130%, “11” - 140%. 
BIAS[5:0] – reserved 
Reserved 
Common control K 
COMK[7] – HREF edge latched by PCLK falling edge. “0” HREF edge is 10 ns after 
PCLK rising edge.  
COMK[6] – Output port drive current additional 2x control bit. 
COMK[5] – reserved. 
COMK[4] – ZV port Vertical timing selection. “1” VSYNC output ZV port vertical 
sync signal. “0” = normal TV vertical sync signal. 
COMK[3] – Quick stable mode when camera mode change. After relative control bit 
set, the first VS will be the stable image with suitable AEC/AWB setting. “0” - slow 
mode, after mode change need more field/frame to get stable AEC/AWB setting 
image. 
COMK[2] – reserved 
COMK[1] – AWB stable time selection when in slow mode. “1” - 4 times less time 
needed to get stable AWB setting when in slow AWB mode. 
COMK[0] – reserved. 
Note: 
COMK[1] (AWB stable Time) is not programmable on the OV6130 image sensor. 
Common control L 
COML[7] – reserved 
COML[6] – PCLK output timing selection. “1” - PCLK valid only when HREF is high; 
“0” - PCLK is free running. 
COML[5] – reserved. 
COML[4] – “1” select CHSYNC output from HREF port. “0” normal 
COML[3] – “1” select HREF output from CHSYNC port. “0” normal 
2C 
2D 
Rsvd 2C 
COMJ 
88 
03 
RW 
RW 
2E 
VCOFF 
80 
RW 
2F – 32 
33 
Rsvd 2F–32 
CPP 
××
00 
– 
RW 
34 
BIAS 
A2 
RW 
35-37 
38 
Rsvd 35-37 
COMK 
80 
81 
RW 
RW 
39 
COML 
00 
RW