
S INGLE IC CMOS  COLOR AND B/W DIGIT AL CAMERAS
March 4, 2000 
Version 1.0 
26 
COMF[1] – “1” digital offset adjustment enable. “0” disable. 
COMF[0] – “1” Output first 4 line black level before valid data output. HREF number 
will increase 4 relatively. “0” no black level output. 
Common control G 
COMG[7:6] – reserved 
COMG[5] - Select CKOUT pin output V flag. “1” - CKOUT output V flag signal. 
CKOUT=1 if UV channel output V or Red. CKOUT=0 if UV channel output U or 
BLUE. “0” - CKOUT output buffered XCLK2 
COMG[4:3] – reserved. 
COMG[2] – “1” digital offset adjustment manually mode enable. Digital data will be 
add/subtract a value defined by register [21] and [22], the contents are programmed 
through I
2
C. “0” - digital data will be added/subtract a value defined by register [21] 
and [22], which are updated by internal circuit. 
COMG[1] – Digital output full range selection. OV6630/OV6130 default output data 
range is [10] - [F0]. The output range changes to [01] - [FE] with signal overshoot 
and undershoot level if COMG[1]=1. 
COMG[0] – reserved. 
Common control H 
COMH[7] – “1” selects one-line RGB raw data output format, “0” selects normal two-
line RGB raw data output. 
COMH[6] – “1” enable black/white mode. The vertical resolution will be higher than 
color mode when the imager works as BW mode. OV6630/OV6130 can’t work at 8-
bit output in this mode. OV6630/OV6130 outputs data from Y port. UV port will be 
tri-state. COMB[5] and COMB[4] will be set to “0”. “0” normal color mode. 
COMH[5] – reserved. 
COMH[4] – Freeze AEC/AGC value, effective only at COMB[0]=1. “1” - register [00] 
and [10] will not be updated and hold latest value. “0” - AEC/AGC normal working 
status. 
COMH[3] – AGC disable. “1” - when COMB[0]=1 and COMA[5]=1, internal circuit 
will not update register [00], register [00] will kept latest updated value before 
COMH[3]=1. “0” - when COMB0=1 and COMA[5]=1, register [00] will be updated 
by internal algorithm. 
COMH[2] – RGB raw data output YG format: “1” - Y channel G, UV channel B R; “0” 
- Y channel: G R G R 
···
, UV channel B G B G 
···
COMH[1] – Gain control bit. “1” channel gain increases 6dB. “0” no change to the 
channel gain. 
COMH[0] – reserved. 
Note: 
COMH[2] (RGB Raw Data) is not programmable on the OV6130 image sensor. 
Common control I 
COMI[7] – AEC disable. “1” If COMB[0]=1, AEC stop and register [10] value will be 
held at last AEC value and not be updated by internal circuit. “0” - if COMB[0]=1, 
register [10] value will be updated by internal circuit 
COMI[6] – Slave mode selection. “1” slave mode, use external SYNC and VSYNC; 
“0” master mode. 
COMI[5:4] – reserved 
COMI[3] – Central 1/4 image area rather whole image used to calculate AEC/AGC. “0” 
use whole image area to calculate AEC/AGC. 
COMI[2] – reserved 
COMI[1:0] – Version flag. For version A, value is [00], these two bits are read only. 
Frame rate adjust high 
FRARH[7] – Frame Rate adjustment enable bit. “1” Enable.  
FRARH[6] – reserved 
FRARH[5] – Highest 1bit of frame rate adjust control byte. See explanation below. 
FRARH[4] – reserved 
FRARH[3] – Y channel brightness adjustment enable. When COMF[2]=1 active. 
FRARH[2] – reserved  
FRARH[1] – “1” When in Frame exposure mode, only One frame data output. 
FRARH[0] – reserved 
Frame rate adjust low 
FRARL[7:0] – Lowest 8 bit of frame rate adjust control byte. Frame rate adjustment 
27 
COMG 
A0 
RW 
28 
COMH 
01 
RW 
29 
COMI 
00 
RW 
2A 
FRARH 
84 
RW 
2B 
FRARL 
5E 
RW