
S INGLE IC CMOS  COLOR AND B/W DIGIT AL CAMERAS
March 4, 2000 
Version 1.0 
25 
COME[2] – reserved. 
COME[1] – AWB fast/slow mode selection. “1” - AWB is always fast mode, that is 
register [01] and [02] is changed every field. “0” AWB is slow mode, [01] and [02] 
change every 16/ 64 field decided by COMK[1]. When AWB enable, COMA[2]=1, 
AWB is working as fast mode until it reaches stable, than as slow mode. 
COME[0] – Digital output driver capability increase selection: “1” Double digital 
output driver current; “0” low output driver current status. 
Note: 
COME[3] (AWB smart mode), COME[2] (AWB stop),  and COME[1] (AWB 
fast/slow) are not programmable on the OV6130 image sensor. 
Y channel offset adjustment 
YOFF[7] – Offset adjustment direction 0 - Add Y[6:0]; 1 -Subtract Y[6:0].  
YOFF[6:0] –Y channel digital output offset adjustment. Range: +127 ~ -127. If 
COMG[2]=0, this register will be updated by internal circuit. Write a value to this 
register through I
2
C has no effect. COMG[2]=1, Y channel offset adjustment will use 
the stored value which can be changed through I
2
C. This register has no effect to A/D 
output data if COMF[1]=0. If output RGB raw data, this register will adjust R/G/B 
data. 
U Channel offset adjustment 
UOFF[7] – Offset adjustment direction: 0 - Add U[6:0]; 1 - Subtract U[6:0]. 
UOFF[6:0] – U channel digital output offset adjustment. Range: +128 ~ -128. If 
COMG[2]=0, this register will be updated by internal circuit. Write a value to this 
register through I
2
C has no effect. COMG[2]=1, U channel offset adjustment will use 
the stored value which can be changed through I
2
C. This register has no effect to A/D 
output data if COMF[1]=1. If output RGB raw data, this register will adjust R/G/B 
data. 
Note: 
This function is not available on the OV6130 image sensor. 
Oscillator circuit control 
CLKC[7:6] – Select different crystal circuit power level (“11” = minimum). 
CLKC[5:0] – reserved 
Automatic exposure control: Bright pixel ratio adjustment 
AEW[7:0] – Used as calculate bright pixel ratio. OV6630/OV6130 AEC algorithm is 
count whole field bright pixel (its luminance level is higher than a fixed level) and 
black pixel (its luminance level is lower than a fixed level) number. When 
bright/black pixel ratio is same as the ratio defined by register [25] and [26], image 
stable. This register is used to define bright pixel ratio, default is 25%, each LSB 
represent step: 0.5% Change range is: [01] ~ [CA]; Increase AEW[7:0] will increase 
bright pixel ratio. For same light condition, the image brightness will increase if 
AEW[7:0] increase.  
Note: 
AEW[7:0] must combine with register [26] AEB[7:0]. The relation must be as 
follows: AEW[7:0] + AEB[7:0] > [CA]. 
Automatic Exposure Control: Black pixel ratio adjustment 
AEB[7:0] – used as calculate black pixel ratio. OV6630 AEC algorithm is count whole 
field/ frame bright pixel (its luminance level is higher than a fixed level) and black 
pixel (its luminance level is lower than a fixed level) number. When bright/black 
pixel ratio is same as the ratio defined by register [25] and [26], image stable. This 
register is used to define black pixel ratio, default is 80%, each LSB represent step: 
0.5%; Change range is: [01] ~ [CA]; Increase AEB[7:0] will increase black pixel 
ratio. For same light condition, the image brightness will decrease if AEB[7:0] 
increase.  
Note: 
AEB[7:0] must e combined with register [25] AEW[7:0]. The relation must be as fol-
lows: AEW[7:0] + AEB[7:0] > [CA]. 
Common control F 
COMF[7:4] – reserved. 
COMF[3] – UV offset difference. “1” use separate offsets for U and V; “0” use one 
offset for both U and V. 
COMF[2] – Digital data MSB/LSB swap. “1” LSB
→
bit7, MSB
→
bit0; “0” normal. 
21 
YOFF 
80 
RW 
22 
UOFF 
80 
RW 
23 
CLKC 
04 
RW 
24 
AEW 
33 
RW 
25 
AEB 
97 
RW 
26 
COMF 
B0 
RW