- 您現在的位置：買賣IC網 > PDF目錄383645 > MT9076 (Mitel Networks Corporation) T1/E1/J1 3.3V Single Chip Transceiver(T1/E1/J1 3.3V 單片收發器) PDF資料下載
參數資料
| 型號： | MT9076 |
| 廠商： | Mitel Networks Corporation |
| 英文描述： | T1/E1/J1 3.3V Single Chip Transceiver(T1/E1/J1 3.3V 單片收發器) |
| 中文描述： | T1/E1/J1收發3.3V的單芯片收發器（T1/E1/J1收發3.3單片收發器） |
| 文件頁數： | 50/162頁 |
| 文件大?。?/td> | 427K |
| 代理商： | MT9076 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁當前第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁
MT9076
Preliminary Information
46
10.2.1
1) The basic frame alignment, signaling multiframe alignment, and CRC-4 multiframe alignment functions
operate in parallel and are independent.
2) The receive channel associated signaling bits and signaling multiframe alignment bit will be frozen when
multiframe alignment is lost.
3) Manual re-framing of the receive basic frame alignment and signaling multiframe alignment functions can be
performed at any time.
4) The transmit RAI bit will be one until basic frame alignment is established, then it will be zero.
5) E-bits can be optionally set to zero until the equipment interworking relationship is established. When this
has been determined one of the following will take place:
a) CRC-to-non-CRC operation - E-bits = 0,
b) CRC-to-CRC operation - E-bits as per G.704 and I.431.
6) All manual re-frames and new basic frame alignment searches start after the current frame alignment signal
position.
7) After basic frame alignment has been achieved, loss of frame alignment will occur any time three
consecutive incorrect basic frame alignment signals are received. Loss of basic frame alignment will reset
the complete framing algorithm.
8) When CRC-4 multiframing has been achieved, the primary basic frame alignment and resulting multiframe
alignment will be adjusted to the basic frame alignment determined during CRC-4 synchronization.
Therefore, the primary basic frame alignment will not be updated during the CRC-4 multiframing search, but
will be updated when the CRC-4 multiframing search is complete.
Notes for Synchronization State Diagram (Figure 16)
10.3
Reframe
10.3.1
The MT9076 will automatically force a reframe, if three consecutive frame alignment patterns or three
consecutive non-frame alignment bits are in error.
E1 Mode
10.3.2
The MT9076 will automatically force a reframe if the framing bit error density exceeds the threshold
programmed by control bits RS1-0 (Framing Mode Select Word page 1H, address 10H). RS1 = RS0 = 0 forces
a reframe for 2 errors out of a sliding window of 4 framing bits. RS1 = 0, RS0 = 1 forces a reframe with 2 errors
out of 5. RS1 = 1, RS0 = 0 forces a reframe with 2 errors out of 6. RS1 = RS0 = 1 disables the automatic
reframe.
T1 Mode
In ESF mode, all framing bits are checked. In D4 mode, either Ft bits only (if control bit 2 - FSI - of Framing
Mode Select Register is set low) or Ft and Fs bits are checked (FSI set high). If the D4 secondary yellow alarm
is enabled (control bit 1 - D4SECY of Transmit Alarm Control Word page 1H, address 11H) then the Fs bit of
frame 12 is not verified for the loss of frame circuit.
In E1 or T1 mode, receive transparent mode (selected when bit 3 page 1 address 12H is high) no reframing is
forced by the device.
The user may initiate a software reframe at any time by setting bit 1, page 1, address 10H high (ReFR). Once
the circuit has commenced reframing the signaling bits are frozen until multiframe synchronization has been
achieved.
11.0 MT9076 Channel Signaling
11.1
Channel Signaling in T1 Mode
In T1 mode, when control bit RBEn (page 1H, address 14H) is low the MT9076 will insert ABCD or AB
signaling bits into bit 8 of every transmit DS0 channel every 6th frame. The AB or ABCD signaling bits from
received frames 6 and 12 (AB) or from frames 6, 12, 18 and 24 (ABCD) will be loaded into an internal storage
相關PDF資料 |
PDF描述 |
|---|---|
| MT9079 | Advanced Controller for E1(先進的E1幀調節器和控制器) |
| MT9080B | SMX - Switch Matrix Module(用于消費類轉換應用的開關矩陣模塊) |
| MT90810 | Flexible MVIP(Multi-Vendor Integration Protocol) Interface Circuit(彈性MVIP接口電路) |
| MT90812 | Integrated Digital Switch (IDX)(集成數字開關) |
| MT90840AK | Distributed Hyperchannel Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT9076AB | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:T1/E1/J1 3.3V Single Chip Transceiver |
| MT9076AP | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:T1/E1/J1 3.3V Single Chip Transceiver |
| MT9076B | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1/J1 3.3 V Single Chip Transceiver |
| MT9076BB | 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/J1/T1 3.3V 80LQFP - Trays |
| MT9076BB1 | 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/J1/T1 3.3V 80LQFP - Trays |
發布緊急采購，3分鐘左右您將得到回復。