參數資料
型號： MT9076
廠商： Mitel Networks Corporation
英文描述： T1/E1/J1 3.3V Single Chip Transceiver(T1/E1/J1 3.3V 單片收發器)
中文描述： T1/E1/J1收發3.3V的單芯片收發器（T1/E1/J1收發3.3單片收發器）
文件頁數： 22/162頁
文件大?。?/td> 427K
代理商： MT9076
MT9076
Preliminary Information
18
Figure 4 - Input Jitter Tolerance as Recommended by G.823 and ETSI 300 011 (E1)
1.2
Transmitter
The transmit portion of the MT9076 LIU consists of a high speed digital-to-analog converter and
complementary line drivers.
When a pulse is to be transmitted, a sequence of digital values (dependent on transmit equalization) are read
out of a ROM by a high speed clock. These values drive the digital-to-analog converter to produce an analog
signal, which is passed to the complementary line drivers.
The complementary line drivers are designed to drive a 1:2.4 step-up transformer in T1 mode (see Figure 4 for
T1 mode) and either a 1:2 or 1:2.4 step-up transformer in E1 mode (see Figure 5 for E1 mode). A 0.47uF
capacitor is required between the TTIP and the transmit transformer. Resistors RT (as shown in Figure 4) are
for termination for transmit return loss. The values of RT may be optimized for T1 mode, E1 120
lines, E1 75
lines or set at a compromise value to serve multiple applications. Program the Tx LIU Control Word (page 02H,
address 11H) to adjust the pulse amplitude accordingly.
Alternatively, the pulse level and shape may be discretely programmed by writing to the Custom Pulse Level
registers (page 2, addresses 1CH to 1FH) and setting the Custom Transmit Pulse bit high (bit 3 of the Tx LIU
Control Word). In this case the output of each of the registers directly drives the D/A converter going to the line
driver. Tables 1 and 2 show recommended transmit pulse amplitude settings.
In T1 mode, the template for the transmitted pulse (the DSX-1 template) is shown in Figure 8. The nominal
peak voltage of a mark is 3 volts. The ratio of the amplitude of the transmit pulses generated by TTIP and
TRING lie between 0.95 and 1.05.
In E1 mode, the template for the transmitted pulse, as specified in G.703, is shown in Figure 8. The nominal
peak voltage of a mark is 3 volts for 120
twisted pair applications and 2.37 volts for 75
coax applications.
The ratio of the amplitude of the transmit pulses generated by TTIP and TRING lie between 0.95 and 1.05.
18UI
1.5UI
0.2UI
1.667Hz
20Hz
2.4kHz 18kHz 100kHz
Peak to Peak
Jitter Amplitude
(log scale)
Jitter Frequency
(log scale)
MT9076
Tolerance
相關PDF資料
PDF描述
MT9079 Advanced Controller for E1(先進的E1幀調節器和控制器)
MT9080B SMX - Switch Matrix Module(用于消費類轉換應用的開關矩陣模塊)
MT90810 Flexible MVIP(Multi-Vendor Integration Protocol) Interface Circuit(彈性MVIP接口電路)
MT90812 Integrated Digital Switch (IDX)(集成數字開關)
MT90840AK Distributed Hyperchannel Switch
相關代理商/技術參數
參數描述
MT9076AB 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:T1/E1/J1 3.3V Single Chip Transceiver
MT9076AP 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:T1/E1/J1 3.3V Single Chip Transceiver
MT9076B 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1/J1 3.3 V Single Chip Transceiver
MT9076BB 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/J1/T1 3.3V 80LQFP - Trays
MT9076BB1 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/J1/T1 3.3V 80LQFP - Trays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*