參數資料
型號： MC68HC11F1CFN4R2
廠商： Freescale Semiconductor
文件頁數： 121/158頁
文件大?。?/td> 0K
描述： IC MCU 1K RAM 4MHZ 68-PLCC
標準包裝： 1
系列： HC11
核心處理器： HC11
芯體尺寸： 8-位
速度： 4MHz
連通性： SCI，SPI
外圍設備： POR，WDT
輸入/輸出數： 30
程序存儲器類型： ROMless
EEPROM 大小： 512 x 8
RAM 容量： 1K x 8
電壓 - 電源 (Vcc/Vdd)： 4.75 V ~ 5.25 V
數據轉換器： A/D 8x8b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 68-LCC（J 形引線）
包裝： 剪切帶 (CT)
其它名稱： MC68HC11F1CFN4RCT
RESETS AND INTERRUPTS
TECHNICAL DATA
5-3
Semiconductor wafer processing causes variations of the RC time-out values between
individual devices. An E-clock frequency below 10 kHz is detected as a clock monitor
error. An E-clock frequency of 200 kHz or more prevents clock monitor errors. Using
the clock monitor function when the E-clock is below 200 kHz is not recommended.
Special considerations are needed when a STOP instruction is executed and the clock
monitor is enabled. Because the STOP function causes the clocks to be halted, the
clock monitor function generates a reset sequence if it is enabled at the time the STOP
mode was initiated. Before executing a STOP instruction, clear to zero the CME bit in
the OPTION register to disable the clock monitor. After recovery from STOP, set the
CME bit to logic one to enable the clock monitor.
5.1.5 OPTION Register
*Can be written only once in first 64 cycles out of reset in normal modes, or at any time in special modes.
ADPU — Analog-to-Digital Converter Power-Up
CSEL — Clock Select
IRQE — Configure IRQ for Edge-Sensitive Only Operation
0 = Low level sensitive operation.
1 = Falling edge sensitive only operation.
DLY — Enable Oscillator Start-up Delay
0 = The oscillator start-up delay coming out of STOP is bypassed and the MCU re-
sumes processing within about four bus cycles.
1 = A delay of approximately 4000 E-clock cycles is imposed as the MCU is started
up from the STOP power-saving mode.
CME — Clock Monitor Enable
This control bit can be read or written at any time and controls whether or not the in-
ternal clock monitor circuit triggers a reset sequence when the system clock is slow or
absent. When it is clear, the clock monitor circuit is disabled, and when it is set, the
clock monitor circuit is enabled. Reset clears the CME bit.
FCME — Force Clock Monitor Enable
To use STOP mode, the FCME bit must equal zero.
0 = Clock monitor follows the state of the CME bit.
1 = Clock monitor circuit is enabled until next reset
OPTION — System Configuration Options
$1039
Bit 7
654321
Bit 0
ADPU
CSEL
IRQE*
DLY*
CME
FCME*
CR1*
CR0*
RESET:
0001000
0
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相關PDF資料
PDF描述
AR215A102K4R CAP CER 1000PF 50V 10% RADIAL
AR201A102K4R CAP CER 1000PF 100V 10% RADIAL
P30G472J1-F CAP CER 4700PF 100V 5% AXIAL
1828857-3 KIT,LC LGTCRP+,JACK 50/125
1828857-2 KIT,LC LGTCRP+,JACK 50/125
相關代理商/技術參數
參數描述
MC68HC11F1CFN5 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Technical Summary 8-Bit Microcontroller
MC68HC11F1CFU 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11F1CFU1 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11F1CFU3 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11F1CFU4 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*