參數資料
型號: MC56F8347VVFE
廠商: Freescale Semiconductor
文件頁數: 10/172頁
文件大?。?/td> 0K
描述: IC DGTL SIGNAL CTLR 160-MAPBGA
標準包裝: 126
系列: 56F8xxx
核心處理器: 56800E
芯體尺寸: 16-位
速度: 60MHz
連通性: CAN,EBI/EMI,SCI,SPI
外圍設備: POR,PWM,溫度傳感器,WDT
輸入/輸出數: 76
程序存儲器容量: 136KB(68K x 16)
程序存儲器類型: 閃存
RAM 容量: 6K x 16
電壓 - 電源 (Vcc/Vdd): 2.25 V ~ 3.6 V
數據轉換器: A/D 16x12b
振蕩器型: 外部
工作溫度: -40°C ~ 105°C
封裝/外殼: 160-BGA
包裝: 托盤
配用: MC56F8367EVME-ND - EVAL BOARD FOR MC56F83X
Register Descriptions
56F8347 Technical Data, Rev.11
Freescale Semiconductor
107
Preliminary
6.5.1.2
EMI_MODE (EMI_MODE)—Bit 6
This bit reflects the current (non-clocked) state of the EMI_MODE pin. During reset, this bit, coupled with
the EXTBOOT signal, is used to initialize address bits [19:16] either as GPIO or as address. These settings
can be explicitly overwritten using the appropriate GPIO peripheral enable register at any time after reset.
In addition, this pin can be used as a general purpose input pin after reset.
0 = External address bits [19:16] are initially programmed as GPIO
1 = When booted with EXTBOOT = 1, A[19:16] are initially programmed as address. If EXTBOOT is 0,
they are initialized as GPIO.
6.5.1.3
OnCE Enable (OnCE EBL)—Bit 5
0 = OnCE clock to 56800E core enabled when core TAP is enabled
1 = OnCE clock to 56800E core is always enabled
6.5.1.4
Software Reset (SW RST)—Bit 4
This bit is always read as 0. Writing a 1 to this bit will cause the part to reset.
6.5.1.5
Stop Disable (STOP_DISABLE)—Bits 3–2
00 - Stop mode will be entered when the 56800E core executes a STOP instruction
01 - The 56800E STOP instruction will not cause entry into Stop mode; STOP_DISABLE can be
reprogrammed in the future
10 - The 56800E STOP instruction will not cause entry into Stop mode; STOP_DISABLE can then only be
changed by resetting the device
11 - Same operation as 10
6.5.1.6
Wait Disable (WAIT_DISABLE)—Bits 1–0
00 - Wait mode will be entered when the 56800E core executes a WAIT instruction
01 - The 56800E WAIT instruction will not cause entry into Wait mode; WAIT_DISABLE can be
reprogrammed in the future
10 - The 56800E WAIT instruction will not cause entry into Wait mode; WAIT_DISABLE can then only be
changed by resetting the device
11 - Same operation as 10
6.5.2
SIM Reset Status Register (SIM_RSTSTS)
Bits in this register are set upon any system reset and are initialized only by a Power-On Reset (POR). A
reset (other than POR) will only set bits in the register; bits are not cleared. Only software should only clear
this register.
Figure 6-4 SIM Reset Status Register (SIM_RSTSTS)
Base + $1
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Read
0
SWR
COPR
EXTR
POR
0
Write
RESET
0
00
0
相關PDF資料
PDF描述
MC56F8147VVFE IC DGTL SIGNAL CTLR 160-MAPBGA
MAC7101MAG40 IC MCU 32BIT FLASH 144-LQFP
KMC9328MX1DVM20 IC MCU I.MX 200MHZ 256-MAPBGA
KMC9328MX1CVM15 IC MCU I.MX 150MHZ 256-PBGA
MC9S12C96CFUER IC MCU 16BIT 4K FLASH 80-QFP
相關代理商/技術參數
參數描述
MC56F8355 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:16-Bit Digital Signal Controllers
MC56F8355MFG60 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:16-bit Hybrid Controllers
MC56F8355MFGE 功能描述:數字信號處理器和控制器 - DSP, DSC 16 BIT HYBRID CONTROLLER RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
MC56F8355VFG60 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:16-bit Hybrid Controllers
MC56F8355VFGE 功能描述:數字信號處理器和控制器 - DSP, DSC 16 BIT HYBRID CNTRLR RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT