- 您現在的位置：買賣IC網 > PDF目錄1948 > MC33989DWR2 (Freescale Semiconductor)IC SYSTEM BASE W/CAN 28-SOIC PDF資料下載
參數資料
| 型號： | MC33989DWR2 |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 13/72頁 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM BASE W/CAN 28-SOIC |
| 標準包裝： | 1 |
| 控制器類型： | 系統基礎芯片 |
| 接口： | CAN |
| 電源電壓： | 5.5 V ~ 18 V |
| 電流 - 電源： | 45mA |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 28-SOIC W |
| 包裝： | 剪切帶 (CT) |
| 配用： | KIT33989DWEVB-ND - KIT EVAL 33989DW HS SBC |
| 其它名稱： | MC33989DWR2CT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
Analog Integrated Circuit Device Data
20
Freescale Semiconductor
33989
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
FUNCTIONAL DEVICE OPERATION
DEVICE SUPPLY
The device is supplied from the battery line through the VSUP pin. An external diode is required to protect against negative
transients and reverse battery. It can operate from 4.5 V and under the jump start condition at 27 Vdc. This pin sustains standard
automotive voltage conditions such as load dump at 40 V. When VSUP falls below 3.0 V typical the 33989 detects it and stores
the information into the SPI register in a bit called BATFAIL. This detection is available in all operation modes.
The device incorporates a battery early warning function, providing a maskable interrupt when the VSUP voltage is below 6.0
V typical. A hysteresis is included. Operation is only in Normal and Standby modes. VSUP low is reported in the Input/Output
Register (IOR).
VDD1 VOLTAGE REGULATOR
The VDD1 Regulator is a 5.0 V output voltage with output current capability up to 200 mA. It includes a voltage monitoring
circuitry associated with a reset function. The VDD1 regulator is fully protected against overcurrent and short-circuit. It has over
temperature detection warning flags (bit VDDTEMP in MCR and interrupt registers), and overtemperature shutdown with
hysteresis.
V2 REGULATOR
V2 Regulator circuitry is designed to drive an external path transistor increasing output current flexibility. Two pins are used
to achieve the flexibility. Those pins are V2 and V2 control. The output voltage is 5.0 V and is realized by a tracking function of
the VDD1 regulator. The recommended ballast transistor is MJD32C. Other transistors can be used; however, depending upon
the PNP gain an external resistor-capacitor network might be connected. The V2 is the supply input for the CAN cell. The state
of V2 is reported in the IOR (bit V2LOW set to 1 if V2 is below 4.5 V typical).
HS1 VBAT SWITCH OUTPUT
The HS1 output is a 2.0
typical switch from the VSUP pin. It allows the supply of external switches and their associated pull-
up or pull-down circuitry, in conjunction with the wake-up input pins, for example. Output current is limited to 200 mA and HS1 is
protected against short-circuit and has an overtemperature shutdown (bit HS1OT in IOR and bit HS1OT-V2LOW in INT register).
The HS1 output is controlled from the internal register and the SPI. Because of an internal timer, it can be activated at regular
intervals in Sleep and Stop modes. It can also be permanently turned on in Normal or Standby modes to drive loads or supply
peripheral components. No internal clamping protection circuit is implemented, thus a dedicated external protection circuit is
required in case of inductive load drive.
BATTERY FALL EARLY WARNING
Refer to the discussion under the heading: Device Supply.
INTERNAL CLOCK
The device has an internal clock used to generate all timings (Reset, Watchdog, Cyclic Wake-up, Filtering Time, etc.). Two
oscillators are implemented. A high accuracy (±12 percent) used in Normal Request, Normal and Standby modes, and a low
accuracy (±30 percent) used in Sleep and Stop modes.
OPERATIONAL MODES
FUNCTIONAL MODES
The device has four primary operation modes:
1. Standby mode
2. Normal mode
3. Stop mode
4. Sleep mode
All modes are controlled by the SPI. An additional temporary mode called Normal Request mode is automatically accessed
by the device after reset or wake-up from Stop mode. A Reset (RST) mode is also implemented. Special modes and configuration
are possible for debug and program MCU flash memory.
相關PDF資料 |
PDF描述 |
|---|---|
| MC3488ADR2G | IC LINE DRIVER DUAL EIA 8-SOIC |
| MC34940EGR2 | IC IMAGING DEVICE ELEC 24-SOICW |
| MC44BS373CAFCR2 | IC MODULATOR AUD/VID U/V 20-QFN |
| MC44BS374CAEFR2 | IC AUDIO/VIDEO MODULATOR 16-SOIC |
| MC44BS374T1AEFR2 | IC AUDIO/VIDEO MODULATOR 16-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33989PEG | 功能描述:CAN 接口集成電路 SBC-HS RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MC33989PEGR2 | 功能描述:CAN 接口集成電路 SBC-HS RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MC33990D | 功能描述:IC TRANSCEIVER J-1850 BUS 8-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| MC33990DR2 | 功能描述:IC TRANSCEIVER J-1850 BUS 8-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| MC33991DW | 制造商:Freescale Semiconductor 功能描述:Gauge Driver Integrated Circuit |
發布緊急采購，3分鐘左右您將得到回復。