- 您現在的位置：買賣IC網 > PDF目錄382289 > MBM29PL12LM10PBT (Fujitsu Limited) FLASH MEMORY 128 M (16M ?8/8M ?16) BIT PDF資料下載
參數資料
| 型號： | MBM29PL12LM10PBT |
| 廠商： | Fujitsu Limited |
| 英文描述： | FLASH MEMORY 128 M (16M ?8/8M ?16) BIT |
| 中文描述： | 快閃記憶體128米（1,600？8/8M？16）位 |
| 文件頁數： | 33/72頁 |
| 文件大?。?/td> | 1036K |
| 代理商： | MBM29PL12LM10PBT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
MBM29PL12LM
10
33
HiddenROM Mode
(1) HiddenROM Region
The HiddenROM (HiddenROM) feature provides a Flash memory region that the system may access through
a new command sequence. This is primarily intended for customers who wish to use an Electronic Serial Number
(ESN) in the device with the ESN protected against modification. Once the HiddenROM region is protected, any
further modification of that region is impossible. This ensures the security of the ESN once the product is shipped
to the field.
The HiddenROM region is 256 bytes / 128 words in length. After the system writes the HiddenROM Entry
command sequence, it may read the HiddenROM region by using device addresses A
6
to A
0
(A
22
to A
15
are all
“0”). That is, the device sends only program command that would normally be sent to the address to the
HiddenROM region. This mode of operation continues until the system issues the Exit HiddenROM command
sequence, or until power is removed from the device. On power-up, or following a hardware reset, the device
reverts to sending commands to the address.
If you request Fujitsu to program the ESN in the device, please contact a Fujitsu representative for more
information.
(2) HiddenROM
Entry Command
The device has a HiddenROM region with One Time Protect function. This area is to enter the security code
and to unable the change of the code once set. Programming is allowed in this area until it is protected. However,
once it gets protected, it is impossible to unprotect. Therefore, extreme caution is required.
The HiddenROM region is 256 bytes / 128 words. This area is in SA0 . Therefore, write the HiddenROM entry
command sequence to enter the HiddenROM region. It is called HiddenROM mode when the HiddenROM region
appears.
Sectors other than the block area SA0 can be read during HiddenROM mode. Read/program of the HiddenROM
region is possible during HiddenROM mode. Write the HiddenROM reset command sequence to exit the Hid-
denROM mode. Note that any other commands should not be issued than the HiddenROM program/protection/
reset commands during the HiddenROM mode. When you issue the other commands including the suspend
resume capability, send the HiddenROM reset command first to exit the HiddenROM mode and then issue each
command.
(3) HiddenROM
Program Command
To program the data to the HiddenROM region, write the HiddenROM program command sequence during
HiddenROM mode. This command is the same as the usual program command, except that it needs to write
the command during HiddenROM mode. Therefore the detection of completion method is the same as in the
past, using the DQ
7
data pooling, DQ
6
Toggle bit or RY/BY. You should pay attention to the address to be
programmed. If an address not in the HiddenROM region is selected, the previous data will be deleted.
During the write into the HiddenROM region, the program suspend command issuance is prohibited.
(4) HiddenROM
Protect Command
There are two methods to protect the HiddenROM region. One is to write the sector group protect setup command
(60h) , set the sector address in the HiddenROM region and (A
6
, A
3
, A
2
, A
1
, A
0
)
=
(0, 0, 0, 1, 0) , and write the
sector group protect command (60h) during the HiddenROM mode. The same command sequence may be used
because it is the same as the extension sector group protect in the past, except that it is in the HiddenROM
mode and does not apply high voltage to the RESET pin. Please refer to above mentioned “Extended Sector
Group Protection” for details of sector group protect setting.
The other method is to apply high voltage (V
ID
) to A
9
and OE, set the sector address in the HiddenROM region
and (A
6
, A
3
, A
2
, A
1
, A
0
)
=
(0, 0, 0, 1, 0) , and apply the write pulse during the HiddenROM mode. To verify the
protect circuit, apply high voltage (V
ID
) to A
9
, specify (A
6
, A
3
, A
2
, A
1
, A
0
)
=
(0, 0, 0, 1, 0) and the sector address
in the HiddenROM region, and read. When “1” appears on DQ
0
, the protect setting is completed. “0” will appear
on DQ
0
if it is not protected. Apply write pulse again. The same command sequence could be used for the above
method because other than the HiddenROM mode, it is the same as the sector group protect previously men-
tioned.
相關PDF資料 |
PDF描述 |
|---|---|
| MBM29PL12LM10PCN | FLASH MEMORY 128 M (16M ?8/8M ?16) BIT |
| MBM30LV0064-PFTN | 64M (8M X 8) BIT NAND-type |
| MBM30LV0064-PFTR | 64M (8M X 8) BIT NAND-type |
| MBM30LV0032 | 32M (4M X 8) BIT NAND-type |
| MBM30LV0032-PFTN | 32M (4M X 8) BIT NAND-type |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MBM30000 | 功能描述:BRACKET SIDE MOUNT RoHS:是 類別:工業控制，儀表 >> 配件 系列:* 標準包裝:1 系列:Aero-Motive® 130117 附件類型:拖車帶 適用于相關產品:標準盒式跟蹤系統 其它名稱:WM6183 |
| MBM30035001 | 制造商:LG Corporation 功能描述:Card,Technical |
| MBM30035015 | 制造商:LG Corporation 功能描述:Card,Technical |
| MBM300A6 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES |
| MBM300GR12A | 制造商:n/a 功能描述:IGBT Module |
發布緊急采購，3分鐘左右您將得到回復。