- 您現在的位置：買賣IC網 > PDF目錄45179 > MB86960APF-G 2 CHANNEL(S), 10M bps, LOCAL AREA NETWORK CONTROLLER, PQFP100 PDF資料下載
參數資料
| 型號： | MB86960APF-G |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 2 CHANNEL(S), 10M bps, LOCAL AREA NETWORK CONTROLLER, PQFP100 |
| 封裝： | PLASTIC, QFP-100 |
| 文件頁數： | 34/66頁 |
| 文件大小： | 376K |
| 代理商： | MB86960APF-G |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
MB86960
4
PIN DESCRIPTIONS
System Bus Interface Pins
SYMBOL
TYPE
DESCRIPTION
RESET
I
HARDWARE RESET: Active high. A minimum pulse of 300 nanoseconds in duration is required.
This pin resets NICE’s internal pointers and registers to the appropriate state.
Note: NICE must be reset after power start before using.
RDY (RDY)
O
READY: This output is asserted to indicate to the host that NICE is ready to complete the requested
read of write operation. It will also be asserted if the device is unable to respond to the request for a
read or write within 2.4 microsecond, In that case, NICE will also assert INT and the bus read error
status bit, DLCR1<6>, or bus write error status bit DLCR<0>. RDY(RDY) may be an active low or
active high signal as determined by RDYPOL, pin 94. If RDYPOL is a “1”, RDY(RDY) will be active
high. If RDYPOL is tied to a “0”, RDY(RDY) will be an active low signal.
RDYPOL
I
READY POLARITY SELECT: Control input to select the polarity of RDY(RDY), pin 14. When this
pin is tied high, RDY(RDY) will be active high. If RDYPOL is tied low, RDY(RDY) will be an active
low signal.
WE
I
WRITE: The WE pin is an active low input that enables a write operation form the host system to the
buffer memory port or to internal registers selected by system address inputs SA0-3.
RD
I
READ: Active low input specifies that the current transfer between NICE and the host system is a
read from one of NICE’s internal registers or its data port as selected by SA0-3.
CS
I
CHIP SELECT: This active low input signal is the chip select for NICE.
BHE
I
BYTE HIGH ENABLE: Active Low. This is the byte/word control line. It is used only when NICE is
configured for a 16-bit data bus by the SB/SW bit of DLCR6. It allows word, upper byte only or lower
byte only transfers. The address select pin SA0 is used with BHE for byte or word transfers. as
follows.
SB/SW
BHE
SA0
FUNCTION
0
Word transfer
0
1
Byte transfer on upper half of data bus (SD15-8)
0
1
0
Byte transfer on lower half of data bus (SD7-0)
0
1
Reserved
1X
X
Byte transfer (SD7-0)
INT
O
INTERRUPT: Active low. Indicates that NICE requires host system attention after successful
transmission or reception of a packet or if any error condition occurs, or if an EOP (end of process)
signal from the host occurs after the completion of the DMA cycle. The Interrupt signal is maskable
and can be disabled by writing a 0 to the appropriate mask bit.
EOP(EOP)
I
END OF PROCESS: Indicates to NICE that the DMA transfer is finished. When the host DMA
controller asserts EOP(EOP), further assertion of NICE’s bus request output. DREQ, will be
discontinued.
Note:
Dual function pins have two
names with the second in
parentheses ( ).
B = Bidirectional I/O
I
= Standard Input
O = Totem Pole Output
相關PDF資料 |
PDF描述 |
|---|---|
| MB86965A | 2 CHANNEL(S), 10M bps, LOCAL AREA NETWORK CONTROLLER, PQFP16 |
| MB88151APNF-G-500-JNE1 | OTHER CLOCK GENERATOR, PDSO8 |
| MB88151APNF-G-401-JNEFE1 | OTHER CLOCK GENERATOR, PDSO8 |
| MB88151APNF-G-801-JNERE1 | OTHER CLOCK GENERATOR, PDSO8 |
| MB88151APNF-G-400-JNERE1 | OTHER CLOCK GENERATOR, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB86961A | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:UNIVERSAL INTERFACE FOR 10BASET |
| MB86961APD-G | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:UNIVERSAL INTERFACE FOR 10BASET |
| MB86961APF-G | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:UNIVERSAL INTERFACE FOR 10BASET |
| MB86965 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:EtherCoupler ETHERNET CONTROLLER WITH 10BASE?T TRANSCEIVER |
| MB86965B | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:EtherCoupler ETHERNET CONTROLLER WITH 10BASE?T TRANSCEIVER |
發布緊急采購，3分鐘左右您將得到回復。