參數資料
型號： MAX3301EETJ+T
廠商： Maxim Integrated Products
文件頁數： 8/38頁
文件大?。?/td> 0K
描述： IC USB TXRX OTG 32-TQFN-EP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 2,500
類型： 收發器
規程： USB 2.0
電源電壓： 3 V ~ 4.5 V
安裝類型： 表面貼裝
封裝/外殼： 32-WFQFN 裸露焊盤
供應商設備封裝： 32-TQFN-EP（5x5）
包裝： 帶卷 (TR)
MAX3301E/MAX3302E
USB On-the-Go Transceivers and Charge Pumps
16
______________________________________________________________________________________
2-Wire I2C-Compatible Serial Interface
A register file controls the various internal switches and
operating modes of the MAX3301E/MAX3302E through
a simple 2-wire interface operating at clock rates up to
400kHz. This interface supports data bursting, where
multiple data phases can follow a single address phase.
UART Mode
Set uart_en (bit 6 in control register 1) to 1 to place the
MAX3301E/MAX3302E in UART mode. D+ transfers
data to DAT_VP and SE0_VM transfers data to D- in
UART mode.
General-Purpose Buffer Mode
Set gp_en (bit 7 in special-function register 1) and
dat_se0 (bit 2 in control register 1) to 1, set uart_en (bit 6
in control register 1) to 0, and drive
OE/INT low to place
the MAX3301E/MAX3302E in general-purpose buffer
mode. Control the direction of data transfer with dmi-
nus_dir and dplus_dir (bits 3 and 4 of special-function
register 1, see Tables 2 and 14).
Serial Addressing
The MAX3301E/MAX3302E operate as a slave device
that sends and receives control and status signals
through an I2C-compatible 2-wire interface. The inter-
face uses a serial data line (SDA) and a serial clock line
(SCL) to achieve bidirectional communication between
master(s) and slave(s). A master (typically a microcon-
troller) initiates all data transfers to and from the
MAX3301E/MAX3302E and generates the SCL clock
that synchronizes the data transfer (Figure 13).
The MAX3301E/MAX3302E SDA line operates as both an
input and as an open-drain output. SDA requires a
pullup resistor, typically 4.7kΩ. The MAX3301E/
MAX3302E SCL line only operates as an input. SCL
requires a pullup resistor if there are multiple masters on
the 2-wire interface, or if the master in a single-master
system has an open-drain SCL output.
Each transmission consists of a start condition (see
Figure 14) sent by a master device, the MAX3301E/
MAX3302E 7-bit slave address (determined by the state
of ADD), plus an R/
W bit (see Figure 15), a register
address byte, one or more data bytes, and a stop condi-
tion (see Figure 14).
dplus_dir
dminus_ dir
DIRECTION OF DATA
TRANSFER
00
DAT_VP
→ D+
SE0_VM
→ D-
01
DAT_VP
→ D+
SE0_VM
← D-
10
DAT_VP
← D+
SE0_VM
→ D-
11
DAT_VP
← D+
SE0_VM
← D-
Table 2. Setting the Direction of Data
Transfer in General-Purpose Buffer Mode
SDA
SCL
tHD: STA
tSU: DAT
tHD: DAT
tSU: STA
tHD: STA
tSU: STO
tBUF
tLOW
tHIGH
tR
tF
START
CONDITION
REPEATED START
CONDITION
STOP
CONDITION
START
CONDITION
Figure 13. 2-Wire Serial-Interface Timing Details
相關PDF資料
PDF描述
MS27473T16A8PA CONN PLUG 8POS STRAIGHT W/PINS
MAX13081EASA+T IC TXRX RS485/RS422 8-SOIC
MX574AKEQI+T IC ADC 12BIT W/REF 28-PLCC
MAX3040ESE+T IC RS485/422 TRANS QUAD 16-SOIC
MX7572KEWG12+ IC ADC 12BIT HS 24-SOIC
相關代理商/技術參數
參數描述
MAX3301EEWA+ 制造商:Maxim Integrated Products 功能描述:USB ON-THE-GO TRANSCEIVERS AND CHARGE PUMPS - Rail/Tube
MAX3301EEWA+T 制造商:Maxim Integrated Products 功能描述:USB ON-THE-GO TRANSCEIVER AND CHARGE PUMP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC USB TXRX OTG WLP
MAX3302EEBA 制造商:Maxim Integrated Products 功能描述:USB ON-THE-GO TRANSCEIVER AND CHARG - Rail/Tube
MAX3302EEBA+ 制造商:Maxim Integrated Products 功能描述:USB ON-THE-GO TRANSCEIVERS AND CHARGE PUMPS - Rail/Tube
MAX3302EEBA+T 制造商:Maxim Integrated Products 功能描述:USB ON-THE-GO TRANSCEIVERS AND CHARGE PUMPS - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*