參數資料
型號： MAX3301EETJ+T
廠商： Maxim Integrated Products
文件頁數： 11/38頁
文件大?。?/td> 0K
描述： IC USB TXRX OTG 32-TQFN-EP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 2,500
類型： 收發器
規程： USB 2.0
電源電壓： 3 V ~ 4.5 V
安裝類型： 表面貼裝
封裝/外殼： 32-WFQFN 裸露焊盤
供應商設備封裝： 32-TQFN-EP（5x5）
包裝： 帶卷 (TR)
MAX3301E/MAX3302E
USB On-the-Go Transceivers and Charge Pumps
______________________________________________________________________________________
19
Start and Stop Conditions
Both SCL and SDA assert high when the interface is not
busy. A master device signals the beginning of a trans-
mission with a start (S) condition by transitioning SDA
from high to low while SCL is high. The master issues a
stop (P) condition by transitioning SDA from low to high
while SCL is high. The bus is then free for another trans-
mission (see Figure 14).
Bit Transfer
One data bit is transferred during each clock pulse. The
data on SDA must remain stable while SCL is high (see
Figure 16).
Acknowledge
The acknowledge bit (ACK) is the 9th bit attached to
any 8-bit data word. ACK is always generated by the
receiving device. The MAX3301E/MAX3302E generate
an ACK when receiving an address or data by pulling
SDA low during the ninth clock period. When transmit-
ting data, the MAX3301E/MAX3302E wait for the receiv-
ing device to generate an ACK. Monitoring ACK allows
for detection of unsuccessful data transfers. An unsuc-
cessful data transfer occurs if a receiving device is busy
or if a system fault has occurred. In the event of an
unsuccessful data transfer, the bus master should reat-
tempt communication at a later time.
Slave Address
A bus master initiates communication with a slave
device by issuing a START condition followed by the 7-
bit slave address (see Figure 15). When idle, the
MAX3301E/MAX3302E wait for a START condition fol-
lowed by its slave address. The LSB of the address
word is the read/
write (R/W) bit. R/W indicates whether
the master is writing to or reading from the
MAX3301E/MAX3302E (R/
W = 0 selects the write con-
dition, R/
W = 1 selects the read condition). After
receiving the proper address, the MAX3301E/
MAX3302E issue an ACK.
The MAX3301E/MAX3302E have two possible addresses
(see Table 5). Address bits A6 through A1 are preset,
while a reset condition or an I2C general call address
loads the value of A0 from ADD. Connect ADD to GND to
set A0 to 0. Connect ADD to VL to set A0 to 1. This allows
up to two MAX3301E’s or two MAX3302E’s to share the
same bus.
Write Byte Format
Writing data to the MAX3301E/MAX3302E requires the
transmission of at least 3 bytes. The first byte consists of
the MAX3301E/MAX3302E’s 7-bit slave address, fol-
lowed by a 0 (R/
W bit). The second byte determines
which register is to be written to. The third byte is the
new data for the selected register. Subsequent bytes
are data for sequential registers. Figure 18 shows the
typical write byte format.
Read Byte Format
Reading data from the MAX3301E/MAX3302E requires
the transmission of at least 3 bytes. The first byte con-
sists of the MAX3301E/MAX3302E’s slave address, fol-
lowed by a 0 (R/
W bit). The second byte selects the
register from which data is read. The third byte consists
SDA
SCL
DATA LINE STABLE,
DATA VALID
CHANGE OF DATA
ALLOWED
Figure 16. Bit Transfer
SCL
START
CONDITION
S
SDA BY
TRANSMITTER
SDA BY
RECEIVER
CLOCK PULSE FOR ACKNOWLEDGEMENT
12
8
9
Figure 17. Acknowledge
A
REGISTER ADDRESS
(8 BITS)
MSB
LSB
AA
P
MSB
LSB
DATA
(8 BITS)
S
SLAVE ADDRESS
(7 BITS)
A6
A5
A4
A3
A2
A1
A0
0
R/W
Figure 18. Write Byte Format
相關PDF資料
PDF描述
MS27473T16A8PA CONN PLUG 8POS STRAIGHT W/PINS
MAX13081EASA+T IC TXRX RS485/RS422 8-SOIC
MX574AKEQI+T IC ADC 12BIT W/REF 28-PLCC
MAX3040ESE+T IC RS485/422 TRANS QUAD 16-SOIC
MX7572KEWG12+ IC ADC 12BIT HS 24-SOIC
相關代理商/技術參數
參數描述
MAX3301EEWA+ 制造商:Maxim Integrated Products 功能描述:USB ON-THE-GO TRANSCEIVERS AND CHARGE PUMPS - Rail/Tube
MAX3301EEWA+T 制造商:Maxim Integrated Products 功能描述:USB ON-THE-GO TRANSCEIVER AND CHARGE PUMP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC USB TXRX OTG WLP
MAX3302EEBA 制造商:Maxim Integrated Products 功能描述:USB ON-THE-GO TRANSCEIVER AND CHARG - Rail/Tube
MAX3302EEBA+ 制造商:Maxim Integrated Products 功能描述:USB ON-THE-GO TRANSCEIVERS AND CHARGE PUMPS - Rail/Tube
MAX3302EEBA+T 制造商:Maxim Integrated Products 功能描述:USB ON-THE-GO TRANSCEIVERS AND CHARGE PUMPS - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*