- 您現在的位置：買賣IC網 > PDF目錄9962 > MAX1383ATP+T (Maxim Integrated Products)IC ADC 12BIT 1.25MSPS 20-TQFN PDF資料下載
參數資料
| 型號： | MAX1383ATP+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 11/25頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT 1.25MSPS 20-TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 位數： | 12 |
| 采樣率（每秒）： | 1.25M |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 2 |
| 功率耗散（最大）： | 85.5mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-WQFN 裸露焊盤 |
| 供應商設備封裝： | 20-TQFN-EP（5x5） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 2 個單端，單極；2 個單端，雙極；1 個差分，單極；1 個差分，雙極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁
MAX1377/MAX1379/MAX1383
Dual, 12-Bit, 1.25Msps Simultaneous-Sampling
ADCs with Serial Interface
______________________________________________________________________________________
19
Single-/Dual-Output Modes (S/
D)
In dual-output mode, conversion results from the two
channels appear on separate outputs. DOUT1 outputs
the result from channel 1 and DOUT2 outputs the result
from channel 2. Drive S/D low to operate in dual-output
mode. For DSPs with two-buffer and two-input-stream
capability, use the dual-output mode to allow for easier
DSP software for dual streams. Two buffer locations can
be used so the streams do not need to be separated.
In single-output mode, the results from both channels
appear on DOUT1. The channel 2 conversion result fol-
lows the channel 1 conversion result (see Figure 10).
The MSB (D11) of the channel 2 conversion result
appears on DOUT1 after the 16th rising edge of SCLK.
The LSB (D0) of the channel 2 conversion result
appears on DOUT1 after the 27th rising edge of SCLK
and is ready to be clocked in on the 28th rising edge of
SCLK. DOUT2 is high-impedance when S/D is high.
If CNVST goes high after the 28th rising edge of SCLK,
DOUT1 goes high impedance until the next conversion
is initiated (single-conversion mode). If CNVST goes
high after the 14th rising edge and before the 28th ris-
ing edge of SCLK, DOUT1 is actively driven low until
the next conversion results are ready (continuous- con-
version mode).
Note: In single-output mode, the conversion speed is
limited to 0.625Msps by the maximum SCLK.
Power-Down Modes
Partial Power-Down (PPD)
Reduce power consumption by placing the MAX1377/
MAX1379 in partial power-down mode. Partial power-
down mode is ideal for infrequent data sampling and
applications requiring fast wake-up times. Pull CNVST
high after the 3rd and before the 14th rising edge of
SCLK to place the device in partial power-down mode.
This reduces the analog supply current to 2mA. While
in partial power-down mode, the internal reference
remains enabled (if REFSEL = GND). Figure 11 shows
the timing sequence to enter partial power-down mode.
Full Power-Down Mode (FPD)
Full power-down mode is ideal for infrequent data sam-
pling and very low-supply current applications. To enter
full power-down mode, place the MAX1377/MAX1379/
MAX1383 first in partial power-down mode. Perform the
CNVST/SCLK sequence necessary to enter partial
power-down mode. Repeat the same sequence to enter
full power-down mode. In full power-down mode, the
internal reference is disabled to minimize power con-
sumption. Figure 12 shows the timing sequence to
enter full power-down mode.
Another way to enter the full power-down mode is to
drive CS high. If CS is high, the MAX1377/MAX1379/
MAX1383 act as if the full power-down sequence were
issued. To exit the CS-initiated power-down mode,
drive CS low. Allow 2ms for the reference to wake up
and settle before performing a conversion.
SINGLE CONVERSION
(SINGLE OUTPUT)
CNVST
SCLK
DOUT1
1
8
9
16
17
24
28
CONTINUOUS CONVERSION
(SINGLE OUTPUT)
CNVST
SCLK
DOUT1
1
8
9
16
14
17
24
25
28
27
D11 D10 D9 D8
D7
D6
D5 D4 D3 D2 D1 D0
D11 D10 D9 D8
D7 D6
D5 D4
D3
D2 D1 D0
D11 D10 D9 D8
D7
D6
D5 D4 D3 D2 D1 D0
D11 D10 D9 D8
D7 D6
D5 D4
D3
D2 D1 D0
CHANNEL 1
CONVERSION RESULT
CHANNEL 2
CONVERSION RESULT
HIGH-Z
CHANNEL 1
CONVERSION RESULT
CHANNEL 2
CONVERSION RESULT
0
Figure 10. Single-Output Mode, Single and Continuous Conversions
相關PDF資料 |
PDF描述 |
|---|---|
| MS27484T20B39PC | CONN PLUG 39POS STRAIGHT W/PINS |
| MS27467T21A41SA | CONN PLUG 41POS STRAIGHT W/SCKT |
| D38999/26FG39PD | CONN PLUG 39POS STRAIGHT W/PINS |
| V48B48M250BG3 | CONVERTER MOD DC/DC 48V 250W |
| D38999/26FG39PC | CONN PLUG 39POS STRAIGHT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1385AETM | 制造商:Maxim Integrated Products 功能描述:12-BIT MULTI-CH ADC WITH MULTICH DA - Rail/Tube |
| MAX1385AETM+ | 制造商:Maxim Integrated Products 功能描述: |
| MAX1385BETM | 制造商:Maxim Integrated Products 功能描述:12-BIT MULTI-CH ADC WITH MULTICH DA - Rail/Tube |
| MAX1385BETM+ | 功能描述:射頻放大器 2Ch RF LDMOS Bias Controller RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
| MAX1385BETM+T | 功能描述:射頻放大器 2Ch RF LDMOS Bias Controller RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。