參數資料
型號： MAX1329BETL+
廠商： Maxim Integrated Products
文件頁數： 35/78頁
文件大小： 0K
描述： IC DAS 12BIT 300KSPS 40-TQFN-EP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 50
系列： *
MAX1329/MAX1330
12-/16-Bit DASs with ADC, DACs, DPIOs, APIOs,
Reference, Voltage Monitors, and Temp Sensor
40
______________________________________________________________________________________
REGISTER
NAME
START
READ/
WRITE
(R/
W)
ADDRESS
(ADR<4:0>)
DATA
(D<255:0>, D<23:0>, D<15:0>, OR D<7:0>)
Reserved
0
X
1
0
1
RESERVED, DO NOT USE
Reserved
0
X
1
0
1
0
RESERVED, DO NOT USE
Reserved
0
X
1
0
1
RESERVED, DO NOT USE
Reserved
0
X
1
0
RESERVED, DO NOT USE
Reserved
0
X
1
0
1
RESERVED, DO NOT USE
Reserved
0
X
1
0
RESERVED, DO NOT USE
Reset
0
W
1
XXXXX
X
Table 3. Register Summary (continued)
Note: R/
W = 0 for write, R/W = 1 for read, X = don’t care.
*
Data length can vary from 1 to 16 words, where a word is 16 bits (12 data bits plus 4 address bits).
Register Bit Descriptions
ADC Control Register
The ADC Control register configures the autoconvert
mode, the ADC power-down modes, the ADC reference
buffer, and the internal reference voltage. Changes
made to the ADC Control register settings are applied
immediately. If changes are made during a conversion
in progress, discard the results of that conversion to
ensure a valid conversion result.
AUTO<2:0>: ADC Autoconvert bits (default = 000). The
AUTO<2:0> bits configure the ADC to continuously con-
vert at the selected interval (see Table 4). Calculate the
conversion rate by dividing the ADC master clock fre-
quency by the selected number of clock cycles. For
example, if the ADC master clock frequency is
3.6864MHz and the selected value is 256, the conversion
rate is 3.6864MHz/256 or 14.4ksps. The conversion can
be started with the ADC Direct Write command and runs
continuously using the ADC master clock. Write 000 to
the AUTO<2:0> bits to disable autoconvert mode. When
the autoconvert ADC master clock cycle rate is set to 32
and the acquisition time is set to 32 (AUTO<2:0> = 001,
ACQCK<1:0> = 11, and GAIN<1:0> = 1X), the acquisi-
tion time is automatically reduced to 16 clocks so that the
ADC throughput is less than the autoconversion interval.
The automode operation is unavailable in burst mode.
APD<1:0>: ADC Power-Down bits (default = 00). The
APD<1:0> bits control the power-down states of the
ADC and PGA (see Table 5). When a direct-mode ADC
conversion command is received, the ADC and PGA
power up except when APD<1:0> = 00.
The burst mode outputs data to DOUT directly in real
time as the bit decision is made on the falling edge of
SCLK and the latest conversion result is also stored in
the ADC Data register. For this mode, the conversion
rate is controlled by the SCLK frequency, which is limited
to 5MHz. If the charge pump is enabled, synchronize
SCLK with the CLKIO clock to prevent charge-pump
noise from corrupting the ADC result. Initiate the conver-
sion by writing to the ADC Control register. SCLK is
required to run continuously during the conversion peri-
od. For ADC gains of 1 or 2, a total of 14 to 28 clocks
(two to 16 for acquisition and 12 for conversion) are
required to complete the conversion. For ADC gains of 4
or 8, a total of 16 to 44 clocks (four to 32 for acquisition,
and 12 for conversion) are required to complete the con-
version. Bringing
CS high aborts burst mode.
AREF<1:0>: ADC Reference Buffer bits (default = 00).
The AREF<1:0> bits set the ADC reference buffer gain
when REFE = 0 and the REFADC output voltage when
REFE = 1 (see Table 6). Set AREF<1:0> to 00 to dis-
able the ADC reference buffer and drive REFADC
directly with an external reference.
REFE: Internal Reference Enable bit (default = 0). REFE
= 1 enables the internal reference and sets REFADJ to
2.5V. REFE = 0 disables the internal reference, allowing
an external reference to be applied at REFADJ, which
drives the inputs to the ADC and DAC reference
buffers. The voltage at REFADJ is also used for temper-
ature measurement and must be 2.5V for accurate
results. See the
Temperature Sensor section. This bit is
mirrored in the DAC Control register so that writing
either location updates both bits.
MSB
LSB
NAME
AUTO2
AUTO1
AUTO0
APD1
APD0
AREF1
AREF0
REFE
DEFAULT
00
0000
00
相關PDF資料
PDF描述
MAX13342EEBC+T IC TXRX USB FS 3WIRE 12-UCSP
MAX13410EESA+T IC TXRX RS-485 LDO/CTRL 8-SOIC
MAX1342BETX+ IC ADC/DAC 12BIT W/FIFO 36WQFN
MAX13431EEUB+T TXRX RS-485 16MBPS HALF 10MSOP
MAX13443EASA+T IC TXRX RS485 HALF DUPLEX 8-SOIC
相關代理商/技術參數
參數描述
MAX1329BETL+ 功能描述:ADC / DAC多通道 12-Bit 2Ch 300ksps 5.4V Precision ADC RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40
MAX1329BETL+T 功能描述:ADC / DAC多通道 12-Bit 2Ch 300ksps 5.4V Precision ADC RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40
MAX132C/D 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX132CNG 功能描述:模數轉換器 - ADC Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX132CNG+ 功能描述:模數轉換器 - ADC 18-Bit .1ksps .545V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*