參數資料
型號： MAX1329BETL+
廠商： Maxim Integrated Products
文件頁數： 20/78頁
文件大?。?/td> 0K
描述： IC DAS 12BIT 300KSPS 40-TQFN-EP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 50
系列： *
MAX1329/MAX1330
12-/16-Bit DASs with ADC, DACs, DPIOs, APIOs,
Reference, Voltage Monitors, and Temp Sensor
______________________________________________________________________________________
27
For external clock mode, disable the internal oscillator,
which then configures CLKIO as an input. Apply an
external clock at CLKIO with a frequency up to 20MHz.
The input clock divider can be set to 1, 2, or 4. The out-
put of the CLKIO input divider goes to the input of
charge pump and ADC clock dividers.
Note: When using the internally generated clock, enter-
ing shutdown or sleep mode causes CLKIO to become
an input. To prevent crowbar current, connect a 500k
resistor from CLKIO to DGND.
Digital and Analog Programmable I/Os
The MAX1329/MAX1330 provide four digital programma-
ble I/Os (DPIO1–DPIO4) and four analog programmable
I/Os (APIO1–APIO4). The DPIOs and APIOs can be con-
figured as logic inputs or outputs through the DPIO and
APIO Control registers. The DPIOs are powered by
DVDD. Likewise, the APIOs are powered by AVDD. When
configured as inputs, internal pullups can be enabled
through the DPIO and APIO Setup registers.
Digital Programmable I/O
DPIO1–DPIO4 are powered by DVDD and are program-
mable as the following:
General-purpose input
Wake-up input (internal oscillator enable)
Power-down mode (sleep or shutdown) control input
DAC loading or sequencing input
ADC acquisition and conversion control input
DAC, op amp, and SPDT switch control input
ADC data-ready output
General-purpose output
Analog Programmable I/O
APIO1–APIO4 are powered by AVDD and are program-
mable as the following:
General-purpose input
Wake-up input (internal oscillator enable)
General-purpose output
Digital input/output for signals to be level-shifted
from/to the SPI interface
Temperature Sensor
An internal temperature sensor measures the device
temperature of the MAX1329/MAX1330. The ADC con-
verts the analog measurement from the internal temper-
ature sensor to a digital output (see Table 1). The
temperature measurement resolution is +0.125°C for
each LSB and the measured temperature can be calcu-
lated using the following equation:
T = ADC output data/8°C
where ADC output data is the decimal value of the
two’s complement result.
The MAX1329/MAX1330 support external single-ended
and differential temperature measurements using a diode
connected transistor between AIN1 and AGND, AIN2 and
AGND, or AIN1 and AIN2. Select the appropriate channel
for conversion through the ADC Setup register.
Voltage References
The internal unbuffered 2.5V reference is externally
accessible at REFADJ. Separate ADC and DAC refer-
ence buffers are programmable to output 1.25V, 2.048V,
or 2.5V REFADC and REFDAC. The reference and
buffers can be individually controlled through the ADC
Control and DAC Control registers. Power down the
internal reference to apply an external reference at
REFADJ as an input to the ADC and DAC reference
buffers. Power down the reference buffers to apply exter-
nal references directly at REFADC and REFDAC.
Note: All temperature sensor measurements use the
voltage at REFADJ as a reference and require a 2.5V ref-
erence for accurate results.
Operational Amplifiers
The MAX1329 includes one uncommitted operational
amplifier. The MAX1330 includes two op amps. These
op amps feature rail-to-rail inputs and outputs, with a
bandwidth of 1MHz. The op amps are powered down
through the DAC Control register. An internal analog
switch shorts the negative input to the output when
enabled through the Switch Control register or a DPIO
configured as a switch control input. When powered
down, the outputs of the op amps go high impedance.
ADC OUTPUT DATA
TEMPERATURE
(°C)
TWO’S COMPLEMENT
HEX
+85.000
0010 1010 1000
2A8
+70.000
0010 0011 0000
230
+25.000
0000 1100 1000
0C8
+0.250
0000 0000 0010
002
+0.125
0000 0000 0001
001
0
0000 0000 0000
000
-0.125
1111 1111 1111
FFF
-0.250
1111 1111 1110
FFE
-25.000
1111 0011 1000
F38
-40.000
1110 1100 0000
EC0
Table 1. Temperature vs. ADC Output
相關PDF資料
PDF描述
MAX13342EEBC+T IC TXRX USB FS 3WIRE 12-UCSP
MAX13410EESA+T IC TXRX RS-485 LDO/CTRL 8-SOIC
MAX1342BETX+ IC ADC/DAC 12BIT W/FIFO 36WQFN
MAX13431EEUB+T TXRX RS-485 16MBPS HALF 10MSOP
MAX13443EASA+T IC TXRX RS485 HALF DUPLEX 8-SOIC
相關代理商/技術參數
參數描述
MAX1329BETL+ 功能描述:ADC / DAC多通道 12-Bit 2Ch 300ksps 5.4V Precision ADC RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40
MAX1329BETL+T 功能描述:ADC / DAC多通道 12-Bit 2Ch 300ksps 5.4V Precision ADC RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40
MAX132C/D 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX132CNG 功能描述:模數轉換器 - ADC Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX132CNG+ 功能描述:模數轉換器 - ADC 18-Bit .1ksps .545V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*