- 您現在的位置：買賣IC網 > PDF目錄44991 > LTC3554EPD#TRPB (LINEAR TECHNOLOGY CORP) 0.5 A BATTERY CHARGE CONTROLLER, 1295 kHz SWITCHING FREQ-MAX, PQCC20 PDF資料下載
參數資料
| 型號： | LTC3554EPD#TRPB |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.5 A BATTERY CHARGE CONTROLLER, 1295 kHz SWITCHING FREQ-MAX, PQCC20 |
| 封裝： | 3 X 3 MM, 0.55 MM HEIGHT, LEAD FREE, PLASTIC, UTQFN-20 |
| 文件頁數： | 9/36頁 |
| 文件大?。?/td> | 418K |
| 代理商： | LTC3554EPD#TRPB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
LTC3554
17
3554p
Battery Charger Stability Considerations
The LTC3554’s battery charger contains both a constant-
voltage and a constant-current control loop. The constant-
voltage loop is stable without any compensation when a
battery is connected with low impedance leads. Excessive
lead length, however, may add enough series inductance
to require a bypass capacitor of at least 1μF from BAT to
GND. Furthermore, a 100μF 1210 ceramic capacitor in
series with a 0.3Ω resistor from BAT to GND is required
to keep ripple voltage low if operation with the battery
disconnected is allowed.
High value, low ESR multilayer ceramic chip capacitors
reduce the constant-voltage loop phase margin, possibly
resulting in instability. Ceramic capacitors up to 22μF may
be used in parallel with a battery, but larger ceramics should
be decoupled with 0.2Ω to 1Ω of series resistance.
In constant-current mode, the PROG pin is in the feed-
back loop rather than the battery voltage. Because of the
additional pole created by any PROG pin capacitance,
capacitance on this pin must be kept to a minimum. With
no additional capacitance on the PROG pin, the battery
charger is stable with program resistor values as high
as 25k. However, additional capacitance on this node
reduces the maximum allowed program resistor. The pole
frequency at the PROG pin should be kept above 100kHz.
Therefore, if the PROG pin has a parasitic capacitance,
CPROG, the following equation should be used to calculate
the maximum resistance value for RPROG:
R
PROG ≤
1
2π 100kHz CPROG
NTC Thermistor and Battery Voltage Reduction
The battery temperature is measured by placing a nega-
tive temperature coefcient (NTC) thermistor close to the
battery pack. To use this feature connect the NTC therm-
istor, RNTC, between the NTC pin and ground and a bias
resistor, RNOM, from VBUS to NTC, as shown in Figure 1.
RNOM should be a 1% resistor with a value equal to the
value of the chosen NTC thermistor at 25°C (R25). The
LTC3554 will pause charging when the resistance of the
NTC thermistor drops to 0.54 times the value of R25
or approximately 54k (for a Vishay curve 1 thermistor,
this corresponds to approximately 40°C). If the battery
charger is in constant-voltage mode, the safety timer also
pauses until the thermistor indicates a return to a valid
temperature. As the temperature drops, the resistance of
the NTC thermistor rises. The LTC3554 is also designed
to pause charging when the value of the NTC thermistor
increases to 3.17 times the value of R25. For a Vishay
curve 1 thermistor this resistance, 317k, corresponds to
approximately 0°C. The hot and cold comparators each
have approximately 3°C of hysteresis to prevent oscillation
about the trip point.
Alternate NTC Thermistors and Biasing
The LTC3554 provides temperature qualied charging if
a grounded thermistor and a bias resistor are connected
to NTC. By using a bias resistor whose value is equal to
the room temperature resistance of the thermistor (R25)
the upper and lower temperatures are preprogrammed
to approximately 40°C and 0°C, respectively (assuming
a Vishay curve 1 thermistor).
The upper and lower temperature thresholds can be
adjusted by either a modication of the bias resistor value
or by adding a second adjustment resistor to the circuit.
If only the bias resistor is adjusted, then either the upper
or the lower threshold can be modied but not both. The
other trip point will be determined by the characteristics
of the thermistor. Using the bias resistor in addition to an
adjustment resistor, both the upper and the lower tem-
perature trip points can be independently programmed
with the constraint that the difference between the upper
and lower temperature thresholds cannot decrease.
Examples of each technique are given below.
OPERATION
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3560IS6#TRPBF | 2.1 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO6 |
| LTC3563EDC | 1.75 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO6 |
| LTC3568EDD#TR | 4 A SWITCHING REGULATOR, 4000 kHz SWITCHING FREQ-MAX, PDSO10 |
| LTC3568IDD | 4 A SWITCHING REGULATOR, 4000 kHz SWITCHING FREQ-MAX, PDSO10 |
| LTC3568IDD#TR | 4 A SWITCHING REGULATOR, 4000 kHz SWITCHING FREQ-MAX, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3554EPDTRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Micropower USB Power Manager with Li-Ion Charger and Two Step-Down Regulators |
| LTC3554EUD#PBF | 功能描述:IC USB POWER MANAGER 20UTQFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:PowerPath™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:熱電冷卻器 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.173"，4.40mm 寬）裸露焊盤 供應商設備封裝:28-TSSOP 裸露焊盤 包裝:管件 產品目錄頁面:1410 (CN2011-ZH PDF) |
| LTC3554EUD#TRPBF | 功能描述:IC USB POWER MANAGER 20UTQFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:PowerPath™ 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP（4x4） 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR |
| LTC3554EUD-1#PBF | 功能描述:IC USB POWER MANAGER 20QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:PowerPath™ 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP（4x4） 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR |
| LTC3554EUD-1#TRPBF | 功能描述:IC USB POWER MANAGER 20QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:PowerPath™ 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP（4x4） 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR |
發布緊急采購，3分鐘左右您將得到回復。