- 您現在的位置：買賣IC網 > PDF目錄44991 > LTC3554EPD#TRPB (LINEAR TECHNOLOGY CORP) 0.5 A BATTERY CHARGE CONTROLLER, 1295 kHz SWITCHING FREQ-MAX, PQCC20 PDF資料下載
參數資料
| 型號： | LTC3554EPD#TRPB |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.5 A BATTERY CHARGE CONTROLLER, 1295 kHz SWITCHING FREQ-MAX, PQCC20 |
| 封裝： | 3 X 3 MM, 0.55 MM HEIGHT, LEAD FREE, PLASTIC, UTQFN-20 |
| 文件頁數： | 3/36頁 |
| 文件大?。?/td> | 418K |
| 代理商： | LTC3554EPD#TRPB |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
LTC3554
11
3554p
HPWR (Pin 1): High Power Logic Input. When this pin is
low the input current limit is set to 100mA and when this
pin is driven high it is set to 500mA. The SUSP pin needs
to be low for the input current limit circuit to be enabled.
This pin has a conditional internal pull-down resistor when
power is applied to the VBUS pin.
FSEL (Pin 2): Buck Frequency Select. When this pin is
low the buck switching frequency is set to 1.125MHz and
when this pin is driven high it is set to 2.25MHz.
PBSTAT (Pin 3): Pushbutton Status. This open-drain output
is a debounced and buffered version of the ON pushbutton
input. It may be used to interrupt a microprocessor.
PGOOD (Pin 4): Power Good. This open-drain output
indicates that all enabled buck regulators have been in
regulation for at least 230ms.
ON (Pin 5): Pushbutton Input. Weak internal pull-up
forces a high state if ON is left oating. A normally open
pushbutton is connected from ON to ground to force a
low state on this pin.
FB1 (Pin 6): Feedback Input for Step-Down Switching
Regulator 1. This pin servos to a xed voltage of 0.8V
when the control loop is complete.
FB2 (Pin 7): Feedback Input for Step-Down Switching
Regulator 2. This pin servos to a xed voltage of 0.8V
when the control loop is complete.
PWR_ON2 (Pin 8): Logic Input Enables Step-Down
Switching Regulator 2.
PWR_ON1 (Pin 9): Logic Input Enables Step-Down
Switching Regulator 1.
STBY (Pin 10): Standby Mode. When this pin is driven
high the part enters a very low quiescent current mode.
The buck regulators are each limited to 10mA maximum
load current in this mode.
SW2 (Pin 11): Power Transmission (Switch) Pin for Step-
Down Switching Regulator 2.
BVIN (Pin 12): Power Input for Step-Down Switching
Regulators 1 and 2. It is recommended that this pin be
connected to the VOUT pin. It should be bypassed with a
low impedance multilayer ceramic capacitor.
SW1 (Pin 13): Power Transmission (Switch) Pin for Step-
Down Switching Regulator 1.
CHRG(Pin14):Open-DrainChargeStatusOutput.Thispin
indicates the status of the battery charger. It is internally
pulled low while charging. Once the battery charge cur-
rent reduces to less than one-tenth of the programmed
charge current, this pin goes into a high impedance state.
An external pull-up resistor and/or LED is required to
provide indication.
NTC (Pin 15): The NTC pin connects to a battery’s therm-
istor to determine if the battery is too hot or too cold to
charge. If the battery’s temperature is out of range, charging
is paused until it drops back into range. A low drift bias
resistor is required from VBUS to NTC and a thermistor is
required from NTC to ground. If the NTC function is not
desired, the NTC pin should be grounded.
PROG (Pin 16): Charge Current Program and Charge
Current Monitor Pin. Connecting a resistor from PROG to
ground programs the charge current as given by:
I
CHG (A) =
750V
R
PROG
If sufcient input power is available in constant-current
mode, this pin servos to 1V. The voltage on this pin always
represents the actual charge current.
BAT (Pin 17): Single-Cell Li-Ion Battery Pin. Depending
on available power and load, a Li-Ion battery on BAT will
either deliver system power to VOUT through the ideal
diode or be charged from the battery charger.
VOUT (Pin 18): Output Voltage of the PowerPath Controller
and Input Voltage of the Battery Charger. The majority of
the portable products should be powered from VOUT. The
PIN FUNCTIONS
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3560IS6#TRPBF | 2.1 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO6 |
| LTC3563EDC | 1.75 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO6 |
| LTC3568EDD#TR | 4 A SWITCHING REGULATOR, 4000 kHz SWITCHING FREQ-MAX, PDSO10 |
| LTC3568IDD | 4 A SWITCHING REGULATOR, 4000 kHz SWITCHING FREQ-MAX, PDSO10 |
| LTC3568IDD#TR | 4 A SWITCHING REGULATOR, 4000 kHz SWITCHING FREQ-MAX, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3554EPDTRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Micropower USB Power Manager with Li-Ion Charger and Two Step-Down Regulators |
| LTC3554EUD#PBF | 功能描述:IC USB POWER MANAGER 20UTQFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:PowerPath™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:熱電冷卻器 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.173"，4.40mm 寬）裸露焊盤 供應商設備封裝:28-TSSOP 裸露焊盤 包裝:管件 產品目錄頁面:1410 (CN2011-ZH PDF) |
| LTC3554EUD#TRPBF | 功能描述:IC USB POWER MANAGER 20UTQFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:PowerPath™ 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP（4x4） 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR |
| LTC3554EUD-1#PBF | 功能描述:IC USB POWER MANAGER 20QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:PowerPath™ 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP（4x4） 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR |
| LTC3554EUD-1#TRPBF | 功能描述:IC USB POWER MANAGER 20QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:PowerPath™ 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP（4x4） 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR |
發布緊急采購，3分鐘左右您將得到回復。