- 您現在的位置：買賣IC網 > PDF目錄44991 > LTC3554EPD#TRPB (LINEAR TECHNOLOGY CORP) 0.5 A BATTERY CHARGE CONTROLLER, 1295 kHz SWITCHING FREQ-MAX, PQCC20 PDF資料下載
參數資料
| 型號： | LTC3554EPD#TRPB |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.5 A BATTERY CHARGE CONTROLLER, 1295 kHz SWITCHING FREQ-MAX, PQCC20 |
| 封裝： | 3 X 3 MM, 0.55 MM HEIGHT, LEAD FREE, PLASTIC, UTQFN-20 |
| 文件頁數： | 8/36頁 |
| 文件大?。?/td> | 418K |
| 代理商： | LTC3554EPD#TRPB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
LTC3554
16
3554p
Automatic Recharge
After the battery charger terminates, it will remain off
drawing only microamperes of current from the battery.
If the portable product remains in this state long enough,
the battery will eventually self discharge. To ensure that the
battery is always topped off, a charge cycle will automati-
cally begin when the battery voltage falls below VRECHRG
(typically 4.1V). In the event that the safety timer is run-
ning when the battery voltage falls below VRECHRG, the
timer will reset back to zero. To prevent brief excursions
below VRECHRG from resetting the safety timer, the battery
voltage must be below VRECHRG for more than 1.3ms. The
charge cycle and safety timer will also restart if the VBUS
UVLO cycles low and then high (e.g., VBUS, is removed
and then replaced).
Charge Current
The charge current is programmed using a single resis-
tor from PROG to ground. 1/750th of the battery charge
current is delivered to PROG which will attempt to servo
to 1.000V. Thus, the battery charge current will try to
reach 750 times the current in the PROG pin. The program
resistor and the charge current are calculated using the
following equations:
R
PROG =
750V
I
CHG
,I
CHG =
750V
R
PROG
In either the constant-current or constant-voltage charg-
ing modes, the PROG pin voltage will be proportional to
the actual charge current delivered to the battery. There-
fore, the actual charge current can be determined at any
time by monitoring the PROG pin voltage and using the
following equation:
I
BAT =
V
PROG
R
PROG
750
In many cases, the actual battery charge current, IBAT, will
be lower than ICHG due to limited input current available and
prioritization with the system load drawn from VOUT.
Thermal Regulation
To prevent thermal damage to the IC or surrounding
components, an internal thermal feedback loop will au-
tomatically decrease the programmed charge current if
the die temperature rises to approximately 110°C. Ther-
mal regulation protects the LTC3554 from excessive
temperature due to high power operation or high ambient
thermal conditions and allows the user to push the limits
of the power handling capability with a given circuit board
design without risk of damaging the LTC3554 or external
components. The benet of the LTC3554 thermal regula-
tion loop is that charge current can be set according to the
desired charge rate rather than worst-case conditions with
the assurance that the battery charger will automatically
reduce the current in worst-case conditions.
Charge Status Indication
The CHRG pin indicates the status of the battery charger. An
open-drain output, the CHRG pin can drive an indicator LED
through a current limiting resistor for human interfacing or
simply a pull-up resistor for microprocessor interfacing.
When charging begins, CHRG is pulled low and remains
low for the duration of a normal charge cycle. When charg-
ing is complete, i.e., the charger enters constant-voltage
mode and the charge current has dropped to one-tenth
of the programmed value, the CHRG pin is released (high
impedance). The CHRG pin does not respond to the C/10
threshold if the LTC3554 reduces the charge current due
to excess load on the VOUT pin. This prevents false end
of charge indications due to insufcient power available
to the battery charger. Even though charging is stopped
during an NTC fault the CHRG pin will stay low indicating
that charging is not complete.
OPERATION
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3560IS6#TRPBF | 2.1 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO6 |
| LTC3563EDC | 1.75 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO6 |
| LTC3568EDD#TR | 4 A SWITCHING REGULATOR, 4000 kHz SWITCHING FREQ-MAX, PDSO10 |
| LTC3568IDD | 4 A SWITCHING REGULATOR, 4000 kHz SWITCHING FREQ-MAX, PDSO10 |
| LTC3568IDD#TR | 4 A SWITCHING REGULATOR, 4000 kHz SWITCHING FREQ-MAX, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3554EPDTRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Micropower USB Power Manager with Li-Ion Charger and Two Step-Down Regulators |
| LTC3554EUD#PBF | 功能描述:IC USB POWER MANAGER 20UTQFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:PowerPath™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:熱電冷卻器 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.173"，4.40mm 寬）裸露焊盤 供應商設備封裝:28-TSSOP 裸露焊盤 包裝:管件 產品目錄頁面:1410 (CN2011-ZH PDF) |
| LTC3554EUD#TRPBF | 功能描述:IC USB POWER MANAGER 20UTQFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:PowerPath™ 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP（4x4） 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR |
| LTC3554EUD-1#PBF | 功能描述:IC USB POWER MANAGER 20QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:PowerPath™ 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP（4x4） 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR |
| LTC3554EUD-1#TRPBF | 功能描述:IC USB POWER MANAGER 20QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:PowerPath™ 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP（4x4） 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR |
發布緊急采購，3分鐘左右您將得到回復。