- 您現在的位置：買賣IC網 > PDF目錄44991 > LTC3554EPD#TRPB (LINEAR TECHNOLOGY CORP) 0.5 A BATTERY CHARGE CONTROLLER, 1295 kHz SWITCHING FREQ-MAX, PQCC20 PDF資料下載
參數資料
| 型號： | LTC3554EPD#TRPB |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.5 A BATTERY CHARGE CONTROLLER, 1295 kHz SWITCHING FREQ-MAX, PQCC20 |
| 封裝： | 3 X 3 MM, 0.55 MM HEIGHT, LEAD FREE, PLASTIC, UTQFN-20 |
| 文件頁數： | 25/36頁 |
| 文件大?。?/td> | 418K |
| 代理商： | LTC3554EPD#TRPB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
LTC3554
31
3554p
occur, placing the pushbutton circuitry in the power-down
(PDN1) state. At this point the bucks will be shut down
and PGOOD will go low. Following a one second power-
down period the pushbutton circuitry will enter the hard
reset state (HR).
Holding ON low through the one second power-down
period will not cause a power-up event at end of the one
second period. ON must be brought high following the
power-down event and then go low again for 400ms to
establish a valid power-up event, as shown in Figure 12.
Power-Up Sequencing
Figure 13 shows the actual power-up sequencing of the
LTC3554. Buck1 and buck2 are both initially disabled (0V).
Once the pushbutton has been applied (ON low) for 400ms
buck1 is enabled. Buck1 slews up and enters regulation.
The actual slew rate is controlled by the soft start func-
tion of buck1 in conjunction with output capacitance and
load (see the Step-Down Switching Regulator Operation
section for more information). When buck1 is within about
8% of nal regulation, buck2 is enabled and slews up
into regulation. 230ms after buck2 is within 8% of nal
regulation, the PGOOD output will go high impedance.
The regulators in Figure 13 are slewing up with nominal
output capacitors and no-load. Adding a load or increas-
ing output capacitance on any of the outputs will reduce
the slew rate and lengthen the time it takes the regulator
to get into regulation.
LAYOUT AND THERMAL CONSIDERATIONS
Printed Circuit Board Power Dissipation
In order to be able to deliver maximum charge current
under all conditions, it is critical that the Exposed Pad
on the backside of the LTC3554 package is soldered
to a ground plane on the board. Correctly soldered to a
2500mm2 ground plane on a double-sided 1oz copper
board, the LTC3554 has a thermal resistance (θJA) of
approximately 70°C/W. Failure to make good thermal
contact between the Exposed Pad on the backside of the
package and an adequately sized ground plane will result
in thermal resistances far greater than 70°C/W.
The conditions that cause the LTC3554 to reduce charge
current due to the thermal protection feedback can be
approximated by considering the power dissipated in the
part. For high charge currents the LTC3554 power dis-
sipation is approximately:
PD = (VBUS–BAT) IBAT + PD(REGS)
where PD is the total power dissipated, VBUS is the supply
voltage, BAT is the battery voltage, and IBAT is the battery
charge current. PD(REGS) is the sum of power dissipated
on chip by the step-down switching regulators.
The power dissipated by a step-down switching regulator
can be estimated as follows:
PD(SWx) = (BOUTx IOUT) (100 - Eff)/100
Where BOUTx is the programmed output voltage, IOUT is
the load current and Eff is the % efciency which can
be measured or looked up on an efciency table for the
programmed output voltage.
Thus the power dissipated by all regulators is:
PD(REGS) = PD(SW1) + PD(SW2)
It is not necessary to perform any worst-case power dis-
sipation scenarios because the LTC3554 will automatically
reduce the charge current to maintain the die temperature
at approximately 110°C. However, the approximate ambi-
OPERATION
VOUT2
0.5V/DIV
VOUT1
1V/DIV
0V
3554 F13
100μs/DIV
Figure 13. Power-Up Sequencing
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3560IS6#TRPBF | 2.1 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO6 |
| LTC3563EDC | 1.75 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO6 |
| LTC3568EDD#TR | 4 A SWITCHING REGULATOR, 4000 kHz SWITCHING FREQ-MAX, PDSO10 |
| LTC3568IDD | 4 A SWITCHING REGULATOR, 4000 kHz SWITCHING FREQ-MAX, PDSO10 |
| LTC3568IDD#TR | 4 A SWITCHING REGULATOR, 4000 kHz SWITCHING FREQ-MAX, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3554EPDTRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Micropower USB Power Manager with Li-Ion Charger and Two Step-Down Regulators |
| LTC3554EUD#PBF | 功能描述:IC USB POWER MANAGER 20UTQFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:PowerPath™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:熱電冷卻器 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.173"，4.40mm 寬）裸露焊盤 供應商設備封裝:28-TSSOP 裸露焊盤 包裝:管件 產品目錄頁面:1410 (CN2011-ZH PDF) |
| LTC3554EUD#TRPBF | 功能描述:IC USB POWER MANAGER 20UTQFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:PowerPath™ 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP（4x4） 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR |
| LTC3554EUD-1#PBF | 功能描述:IC USB POWER MANAGER 20QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:PowerPath™ 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP（4x4） 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR |
| LTC3554EUD-1#TRPBF | 功能描述:IC USB POWER MANAGER 20QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:PowerPath™ 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP（4x4） 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR |
發布緊急采購，3分鐘左右您將得到回復。