- 您現在的位置：買賣IC網 > PDF目錄43901 > L99PM62XP (STMICROELECTRONICS) 4-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO36 PDF資料下載
參數資料
| 型號： | L99PM62XP |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 電源管理 |
| 英文描述： | 4-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO36 |
| 封裝： | ROHS COMPLIANT, POWERSSO-36 |
| 文件頁數： | 9/98頁 |
| 文件大?。?/td> | 1117K |
| 代理商： | L99PM62XP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁
L99PM62XP
Description
Doc ID 16363 Rev 2
Note:
Inputs TxDL, TxDC and CSN must be at high level or at high impedance in order to achieve
minimum standby current in V1 standby mode.
Inputs DI and CLK must be at GND or at high impedance to achieve minimum standby
current in V1 standby mode.
Interrupt
The interrupt signal (linked to RxDL/NINT internally) indicates a wake-up event from V1
standby mode. In case of a wake-up by Wake-up Inputs, activity on LIN or CAN, SPI access
or timer-interrupt the NINT pin is pulled low for 56 s.
In case of V1 standby mode and (IV1 > Icmp), the device remains in standby mode, the V1
regulator switches to high current mode and the watchdog starts. No Interrupt signal is
generated.
2.2.4
VBAT standby mode
The transition from active mode to VBAT standby mode is initiated by an SPI command.
In VBAT standby mode, the V1 voltage regulator, relay outputs, LIN and CAN transmitters are
switched off. High-side outputs and the V2 regulator remain in the configuration
programmed prior to the standby command.
In VBAT standby mode the current consumption of the L99PM62XP is reduced to a minimum
level.
Note:
Inputs TXDL, TXDC and CSN must be terminated to GND in VBAT standby to achieve
minimum standby current.
This can be achieved with the internal ESD protection diodes of the microcontroller
(microcontroller is not supplied in this mode; V1 is pulled to GND).
2.2.5
Wake up from standby modes
A wake-up from standby mode switches the device to active mode. This can be initiated by
one or more of the following events:
Table 3.
Wake up sources
Wake up source
Description
LIN bus activity
Can be disabled by SPI
CAN bus activity
Can be disabled by SPI
Level change of WU1 - 3
Can be individually configured or disabled by SPI
IV1 > Icmp
Device remains in V1 standby mode but watchdog is enabled (If
Icmp = 0) and the V1 regulator goes into high current mode (increased
current consumption). No interrupt is generated.
Timer interrupt / wake up
of C by TIMER
Programmable by SPI
–V1 standby mode: device wakes up and Interrupt signal is generated
at RxDL/NINT when programmable timeout has elapsed
–VBAT standby mode: device wakes up, V1 regulator is turned on and
NReset signal is generated when programmable timeout has elapsed
SPI access
Always active (except in VBAT standby mode)
Wake up event: CSN is low and first rising edge on CLK
相關PDF資料 |
PDF描述 |
|---|---|
| LA5635H | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| LA5693D | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 |
| LA5693M | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| LA8638NV | COMPANDER, PDSO30 |
| LA8638V | COMPANDER, PDSO30 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L99PM62XPTR | 功能描述:馬達/運動/點火控制器和驅動器 SPI CNTROL DIAGNOSIS INTERFACE DEVICE RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L99PM72GXPTR | 功能描述:Automotive PMIC PowerSSO-36 制造商:stmicroelectronics 系列:- 包裝:剪切帶（CT） 零件狀態:有效 應用:汽車級 電流 - 電源:6mA 電壓 - 電源:6 V ~ 18 V 工作溫度:-40°C ~ 130°C 安裝類型:表面貼裝 封裝/外殼:36-??FSOP（0.295"，7.50mm 寬） 供應商器件封裝:PowerSSO-36 標準包裝:1 |
| L99SD01-E | 制造商:STMicroelectronics 功能描述:ABD VIPOWER - Rail/Tube |
| L99SD01TR-E | 制造商:STMicroelectronics 功能描述:ABD VIPOWER - Tape and Reel |
| L9A0212 | 制造商:LSI 制造商全稱:LSI 功能描述:Microprocessor |
發布緊急采購，3分鐘左右您將得到回復。