參數資料
型號: L99PM62XP
廠商: STMICROELECTRONICS
元件分類: 電源管理
英文描述: 4-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO36
封裝: ROHS COMPLIANT, POWERSSO-36
文件頁數: 8/98頁
文件大?。?/td> 1117K
代理商: L99PM62XP
Description
L99PM62XP
Doc ID 16363 Rev 2
A cyclic monitoring of wake-up inputs and a periodic interrupt/wake-up by timer is available
in standby modes.
2.2.1
Active mode
All functions are available and the device is controlled by the ST SPI Interface.
2.2.2
Flash mode
To program the system microcontroller, the L99PM62 can be operated in Flash mode where
the internal watchdog is disabled. This mode can also be used for software debugging.
Except for the disabled watchdog, the Flash mode is identical to active mode and all device
features are available.
The mode can be entered if one of the following conditions is applied:
VTxDL > VFlash
VTxDC > VFlash
At exit from Flash mode (VTxD < VFlash) no NReset pulse is generated and the watchdog
starts with a long open window.
Note:
Setting both TxDL and TxDC to high voltage levels (> VFlash) is not allowed
2.2.3
V1 standby mode
The transition from active mode to V1 standby mode is controlled by SPI.
To supply the micro controller in a low power mode, the voltage regulator 1 (V1) remains
active. In order to reduce the current consumption, the regulator goes in low current mode
as soon as the supply current of the microcontroller goes below the Icmp current threshold.
At this transition, the L99PM62 also deactivates the internal watchdog.
Relay outputs, LIN and CAN transmitters is switched off in V1 standby mode. High-side
outputs and the V2 regulator remain in the configuration programmed prior to the standby
command.
A cyclic supply of external contacts and a synchronized monitoring of the contact state can
be activated and configured by SPI.
In V1 standby mode various wake up sources can be individually programmed. Each wake
up event puts the device into active mode and forces the RxDL/NINT pin to a low level
indicating the wake-up condition to the microcontroller.
After power ON reset (POR) all wake up sources are activated by default except the periodic
interrupt/wake timer.
With the interrupt timer the micro controller can be forced from ‘stop’ to ‘run’ after a
programmable period. The RxDL/NINT pin is forced low after the timer is elapsed. The
L99PM62XP enters active mode and is awaiting a valid watchdog trigger.
Both internal timers can be used for this feature.
The interrupt timer (TINT) at pin RxDL/NINT is only available in V1 standby mode.
相關PDF資料
PDF描述
LA5635H SPECIALTY ANALOG CIRCUIT, PDSO28
LA5693D 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8
LA5693M 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8
LA8638NV COMPANDER, PDSO30
LA8638V COMPANDER, PDSO30
相關代理商/技術參數
參數描述
L99PM62XPTR 功能描述:馬達/運動/點火控制器和驅動器 SPI CNTROL DIAGNOSIS INTERFACE DEVICE RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
L99PM72GXPTR 功能描述:Automotive PMIC PowerSSO-36 制造商:stmicroelectronics 系列:- 包裝:剪切帶(CT) 零件狀態:有效 應用:汽車級 電流 - 電源:6mA 電壓 - 電源:6 V ~ 18 V 工作溫度:-40°C ~ 130°C 安裝類型:表面貼裝 封裝/外殼:36-??FSOP(0.295",7.50mm 寬) 供應商器件封裝:PowerSSO-36 標準包裝:1
L99SD01-E 制造商:STMicroelectronics 功能描述:ABD VIPOWER - Rail/Tube
L99SD01TR-E 制造商:STMicroelectronics 功能描述:ABD VIPOWER - Tape and Reel
L9A0212 制造商:LSI 制造商全稱:LSI 功能描述:Microprocessor