參數資料
型號： L99PM62XP
廠商： STMICROELECTRONICS
元件分類： 電源管理
英文描述： 4-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO36
封裝： ROHS COMPLIANT, POWERSSO-36
文件頁數： 14/98頁
文件大小： 1117K
代理商： L99PM62XP
L99PM62XP
Description
Doc ID 16363 Rev 2
watchdog starts with a long open window. After serving the watchdog, the C may send the
device back to V1 standby mode.
After power-on or standby mode, the watchdog is started with a long open window (65 ms
nominal). The long open window allows the micro controller to run its own setup and then to
trigger the watchdog via the SPI. The trigger is processed when the CSN input becomes
HIGH after the transmission of the SPI word.
Writing ‘1’ to the watchdog trigger bit terminates the long open window and start the window
watchdog (the timing is programmable by SPI). Subsequently, the micro controller has to
serve the watchdog by alternating the watchdog trigger bit within the safe trigger area (refer
to Figure 27). A correct watchdog trigger signal is immediately start the next cycle.
After 8 watchdog failures in sequence, the V1 regulator is switched off for 200ms. If
subsequently, 7 additional watchdog failures occur, the V1 regulator is completely turned off
and the device goes into VBAT standby mode until a wakeup occurs.
In case of a watchdog failure, the outputs (RELx, OUTx, V2) are switched off and the device
enters fail-safe mode (i. e. all control registers are set to default values except the ‘OUT3
control bit’).
The following diagrams illustrate the watchdog behavior of the L99PM62. The diagrams are
split into 3 parts. First diagram shows the functional behavior of the watchdog without any
error. The second diagram covers the behavior covering all the error conditions, which can
affect the watchdog behavior. Third diagram shows the transition in and out of Flash mode.
All 3 diagrams can be overlapped to get all the possible state transitions under all
circumstances. For a better readability, they were split in normal operating, operating with
errors and Flash mode.
Figure 9.
Watchdog in normal operating mode (no errors)
WD
OFF
long
open
window
Window
Mode
propper trigger in
Window mode
TRIG = 1'
go Standby
V1 > Vrstthr
VBAT Standby
V1 Standby (I(V1) < ICMP)
Active mode
相關PDF資料
PDF描述
LA5635H SPECIALTY ANALOG CIRCUIT, PDSO28
LA5693D 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8
LA5693M 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8
LA8638NV COMPANDER, PDSO30
LA8638V COMPANDER, PDSO30
相關代理商/技術參數
參數描述
L99PM62XPTR 功能描述:馬達/運動/點火控制器和驅動器 SPI CNTROL DIAGNOSIS INTERFACE DEVICE RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
L99PM72GXPTR 功能描述:Automotive PMIC PowerSSO-36 制造商:stmicroelectronics 系列:- 包裝:剪切帶（CT） 零件狀態:有效 應用:汽車級 電流 - 電源:6mA 電壓 - 電源:6 V ~ 18 V 工作溫度:-40°C ~ 130°C 安裝類型:表面貼裝 封裝/外殼:36-??FSOP（0.295"，7.50mm 寬） 供應商器件封裝:PowerSSO-36 標準包裝:1
L99SD01-E 制造商:STMicroelectronics 功能描述:ABD VIPOWER - Rail/Tube
L99SD01TR-E 制造商:STMicroelectronics 功能描述:ABD VIPOWER - Tape and Reel
L9A0212 制造商:LSI 制造商全稱:LSI 功能描述:Microprocessor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*