- 您現在的位置：買賣IC網 > PDF目錄384585 > L6711TR (意法半導體) 3 PHASE CONTROLLER WITH DYNAMIC VID AND SELECTABLE DACs PDF資料下載
參數資料
| 型號： | L6711TR |
| 廠商： | 意法半導體 |
| 英文描述： | 3 PHASE CONTROLLER WITH DYNAMIC VID AND SELECTABLE DACs |
| 中文描述： | 3相控制器，動態VID和可選數模轉換器 |
| 文件頁數： | 5/38頁 |
| 文件大?。?/td> | 591K |
| 代理商： | L6711TR |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
5/38
L6711
19
CS3+
Channel 3 Current Sense Positive Input pin.
It must be connected through an Rg resistor to the LS mosfet source (or to the GND-side of the
sense resistor placed in series to the LS mosfet) if LS mosfet sense is performed
(CS_SEL=OPEN). Otherwise (CS_SEL=SGND), it must be connected to the phase-side of the
output inductor (or the inductor-side of the sense resistor used and placed between the channel
3 inductor and the output of the converter) through Rg resistor and an R-C network across the
inductor.
The net connecting the pin to the sense point must be routed as close as possible to the CS3-
net in order to couple in common mode any picked-up noise.
Temperature Compensation pin.
Connect through a resistor R
TC
and filter with 10nF vs. SGND to program the temperature com-
pensation effect.
Short to SGND to disable the compensation effect.
Current Reading Selection pin, internally 5V pulled-up.
Leave floating to sense current across low-side mosfets or a sense resistor placed in series to
the LS mosfet source. Maximum duty cycle is dynamically limited and Track&Hold is enabled to
assure proper reading of the current.
Short to SGND to read current across inductors or a sense resistor placed in series to the output
inductors. No duty cycle limitation and no Track&Hold performed in this case.
Oscillator pin.
It allows programming the switching frequency of each channel: the equivalent switching fre-
quency at the load side results in being tripled.
Internally fixed at 1.24V, the frequency is varied proportionally to the current sunk (forced) from
(into) the pin with an internal gain of 6kHz/
μ
A (See relevant section for details).
If the pin is not connected, the switching frequency is 150kHz for each channel (450kHz on the
load).
The pin is forced high (5V Typ.) when an Over/Under Voltage is detected; to recover from this
condition, cycle VCC or the OUTEN pin.
Voltage IDentification pins.
Internally pulled-up to 3V, connect to SGND to program a ‘0’ while leave floating to program a ‘1’.
They are used to program the output voltage as specified in Table 5 and Table 6 together with
VID_SEL and to set the OVP/UVP protection thresholds accordingly.
See relevant section for details about DAC selection.
VID_SELect pin. Through this pin it is possible to select the DAC table used for the regulation.
Leave floating to use a VRD10.x compliant DAC (See Table 1) while short to SGND to use a
VRM-Hammer compliant DAC (See Table 2).
See relevant section for details about DAC selection.
SS_END Soft start end signal. It is an open collector output, set free after finishing the soft start.
Pull-up with a resistor to a voltage lower than 5V, if not used may be left floating.
SGND
All the internal references are referred to this pin. Connect it to the PCB signal ground.
PHASE3
Channel 3 HS driver return path. It must be connected to the HS3 mosfet source and provides
the return path for the HS driver of channel 3.
UGATE3
Channel 3 HS driver output.
A little series resistor helps in reducing device-dissipated power.
BOOT3
Channel 3 HS driver supply. This pin supplies the relative high side driver.
Connect through a capacitor (100nF Typ.) to the PHASE3 pin and through a diode to VCC (cath-
ode vs. boot).
PGND3
Channel 3 LS driver return path.
Connect to Power Ground Plane.
LGATE3
Channel 3 LS driver output.
A little series resistor helps in reducing device-dissipated power.
N.C.
Not internally connected.
20
TC
21
CS_SEL
22
OSC/
FAULT
23, 24 to
28
VID5,
VID0-4
29
VID_SEL
30
31
32
33
34
35
36
37
Table 4. Pin Function
(continued)
N°
Name
Description
相關PDF資料 |
PDF描述 |
|---|---|
| L6714 | 4 phase controller with embedded drivers for Intel VR10, VR11 and AMD 6Bit CPUs |
| L6714TR | 4 phase controller with embedded drivers for Intel VR10, VR11 and AMD 6Bit CPUs |
| L6726A | Single phase PWM controller |
| L6726ATR | Single phase PWM controller |
| L6727 | Single phase PWM controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6712 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:TWO-PHASE INTERLEAVED DC/DC CONTROLLER |
| L6712_05 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:TWO-PHASE INTERLEAVED DC/DC CONTROLLER |
| L6712A | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:TWO-PHASE INTERLEAVED DC/DC CONTROLLER |
| L6712AD | 功能描述:開關變換器、穩壓器與控制器 2-Ph Interleaved RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| L6712ADTR | 功能描述:開關變換器、穩壓器與控制器 2-Ph Interleaved RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。