- 您現在的位置：買賣IC網 > PDF目錄16862 > KSZ8851SNL-EVAL (Micrel Inc)BOARD EVALUATION KSZ8851SNL PDF資料下載
參數資料
| 型號： | KSZ8851SNL-EVAL |
| 廠商： | Micrel Inc |
| 文件頁數： | 6/80頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION KSZ8851SNL |
| 產品培訓模塊： | KSZ8851 10/100 Embedded Controllers |
| 標準包裝： | 1 |
| 系列： | LinkMD® |
| 主要目的： | 接口，以太網控制器（PHY 和 MAC） |
| 嵌入式： | 否 |
| 已用 IC / 零件： | KSZ8851SNL |
| 主要屬性： | 1 個端口，100BASE-TX/10BASE-T |
| 次要屬性： | SPI 接口，LinkMD 線纜診斷 |
| 已供物品： | 板，文檔 |
| 產品目錄頁面： | 1081 (CN2011-ZH PDF) |
| 相關產品： | 576-3299-6-ND - IC CTLR MAC/PHY NON-PCI 32-MLF 576-3299-1-ND - IC CTLR MAC/PHY NON-PCI 32-MLF 576-3299-2-ND - IC CTLR MAC/PHY NON-PCI 32-MLF 576-3254-ND - IC CTLR MAC/PHY NON-PCI 32-QFN |
| 其它名稱： | 576-3293 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
Micrel, Inc.
KSZ8851SNL/SNLI
August 2009
14
M9999-083109-2.0
The KSZ8851SNL will also assert PME output pin if the corresponding enable bit[8] is set in PMECR (0xD4) register or
generate interrupt to signal an energy detect event occurred if the corresponding enable bit[2] is set in IER (0x90) register.
Once the power management unit detects the PME output asserted or interrupt active, it will power up the host CPU and
issue a wakeup command which is any one of registers read or write access to wake up the KSZ8851SNL from the low
power state to the normal power state in case the auto-wakeup enable bit[7] is disabled. When KSZ8851SNL is at normal
power state, it is able to transmit or receive packet from the cable.
Soft Power Down Mode
The soft power down mode is entered by setting bit[1:0]=10 in PMECR register. When KSZ8851SNL is in this mode, all
PLL clocks are disabled, the PHY and the MAC are off, all internal registers value will not change, and the host interface
is only used to wake-up this device from current soft power down mode to normal operation mode.
In order to go back the normal operation mode from this soft power down mode, the only way to leave this mode is
through a host wake-up command which the CPU issues any one of registers read or write access.
Power Saving Mode
The power saving mode is entered when auto-negotiation mode is enabled, cable is disconnected, and by setting
bit[1:0]=11 in PMECR register and bit [10]=1 in P1SCLMD register. When KSZ8851SNL is in this mode, all PLL clocks are
enabled, MAC is on, all internal registers value will not change, and host interface is ready for CPU read or write. In this
mode, it mainly controls the PHY transceiver on or off based on line status to achieve power saving. The PHY remains
transmitting and only turns off the unused receiver block. Once activity resumes due to plugging a cable or attempting by
the far end to establish link, the KSZ8851SNL can automatically enabled the PHY power up to normal power state from
power saving mode.
During this power saving mode, the host CPU can program the bit[1:0] in PMECR register and set bit[10]=0 in P1SCLMD
register to transit the current power saving mode to any one of the other three power management operation modes.
Wake-on-LAN
Wake-up frame events are used to wake the system whenever meaningful data is presented to the system over the
network. Examples of meaningful data include the reception of a Magic Packet, a management request from a remote
administrator, or simply network traffic directly targeted to the local system. In all of these instances, the network device is
pre-programmed by the policy owner or other software with information on how to identify wake frames from other network
traffic. The KSZ8851SNL controller can be programmed to notify the host of the wake-up frame detection with the
assertion of the interrupt signal (INTRN) or assertion of the power management event signal (PME).
A wake-up event is a request for hardware and/or software external to the network device to put the system into a
powered state (working).
A wake-up signal is caused by:
1. Detection of energy signal over a pre-configured value (bit 2 in ISR register)
2. Detection of a linkup in the network link state (bit 3 in ISR register)
3. Receipt of a Magic Packet (bit 4 in ISR register)
4. Receipt of a network wake-up frame (bit 5 in ISR register)
There are also other types of wake-up events that are not listed here as manufacturers may choose to implement these in
their own way.
Detection of Energy
The energy is detected from the cable and is continuously presented for a time longer than pre-configured value,
especially when this energy change may impact the level at which the system should re-enter to the normal power state.
Detection of Linkup
Link status wake events are useful to indicate a linkup in the network’s connectivity status.
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-ADF4007EBZ1 | BOARD EVALUATION FOR ADF4007EB1 |
| V110C12C100B | CONVERTER MOD DC/DC 12V 100W |
| DWP-125-3/4-0-STK | HEATSHRINK POLY 3/4"X4' BLK |
| EBA30DRMD | CONN EDGECARD 60POS .125 SQ WW |
| H2MXH-2618M | DIP CABLE - HDM26H/AE26M/X |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8851SNL-EVAL | 制造商:Micrel Inc 功能描述:BOARD EVALUATION FOR KSZ8851SNL |
| KSZ8851SNLI TR | 功能描述:以太網 IC 10/100BT Ethernet MAC + PHY with SPI Bus Interface (I-Temp, Lead free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8851SNLITR | 制造商:Micrel 功能描述:Ethernet Controller Single Chip 100Mbps |
| KSZ8851SNLI-TR | 功能描述:Ethernet Controller 10/100 Base-T/TX PHY SPI Interface 32-MLF? (5x5) 制造商:microchip technology 系列:- 包裝:剪切帶（CT） 零件狀態:有效 協議:以太網 功能:控制器 接口:SPI 標準:10/100 Base-T/TX PHY 電壓 - 電源:1.8V，2.5V，3.3V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 封裝/外殼:32-VFQFN 裸露焊盤，32-MLF? 供應商器件封裝:32-MLF?（5x5） 標準包裝:1 |
| KSZ8851SNLTR | 制造商:Micrel Inc 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。