- 您現在的位置：買賣IC網 > PDF目錄16862 > KSZ8851SNL-EVAL (Micrel Inc)BOARD EVALUATION KSZ8851SNL PDF資料下載
參數資料
| 型號： | KSZ8851SNL-EVAL |
| 廠商： | Micrel Inc |
| 文件頁數： | 13/80頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION KSZ8851SNL |
| 產品培訓模塊： | KSZ8851 10/100 Embedded Controllers |
| 標準包裝： | 1 |
| 系列： | LinkMD® |
| 主要目的： | 接口，以太網控制器（PHY 和 MAC） |
| 嵌入式： | 否 |
| 已用 IC / 零件： | KSZ8851SNL |
| 主要屬性： | 1 個端口，100BASE-TX/10BASE-T |
| 次要屬性： | SPI 接口，LinkMD 線纜診斷 |
| 已供物品： | 板，文檔 |
| 產品目錄頁面： | 1081 (CN2011-ZH PDF) |
| 相關產品： | 576-3299-6-ND - IC CTLR MAC/PHY NON-PCI 32-MLF 576-3299-1-ND - IC CTLR MAC/PHY NON-PCI 32-MLF 576-3299-2-ND - IC CTLR MAC/PHY NON-PCI 32-MLF 576-3254-ND - IC CTLR MAC/PHY NON-PCI 32-QFN |
| 其它名稱： | 576-3293 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
Micrel, Inc.
KSZ8851SNL/SNLI
August 2009
20
M9999-083109-2.0
Usage
LinkMD
can be run at any time by ensuring that Auto-MDIX has been disabled. To disable Auto-MDIX, write a ‘1’ to
P1CR[10] to enable manual control over the pair used to transmit the LinkMD
pulse. The self-clearing cable diagnostic
test enable bit, P1SCLMD [12], is set to ‘1’ to start the test on this pair.
When bit P1SCLMD[12] returns to ‘0’, the test is complete. The test result is returned in bits P1SCLMD[14:13] and the
distance is returned in bits P1SCLMD[8:0]. The cable diagnostic test results are as follows:
00 = Valid test, normal condition
01 = Valid test, open circuit in cable
10 = Valid test, short circuit in cable
11 = Invalid test, LinkMD
failed
If P1SCLMD[14:13]=11, this indicates an invalid test, and occurs when the KSZ8851SNL is unable to shut down the link
partner. In this instance, the test is not run, as it is not possible for the KSZ8851SNL to determine if the detected signal is
a reflection of the signal generated or a signal from another source.
Cable distance can be approximated by the following formula:
P1SCLMD[8:0] x 0.4m for port 1 cable distance
This constant may be calibrated for different cabling conditions, including cables with a velocity of propagation that varies
significantly from the norm.
Media Access Control (MAC) Operation
The KSZ8851SNL strictly abides by IEEE 802.3 standards to maximize compatibility.
Inter Packet Gap (IPG)
If a frame is successfully transmitted, then the minimum 96-bit time for IPG is measured between two consecutive
packets. If the current packet is experiencing collisions, the minimum 96-bit time for IPG is measured from carrier sense
(CRS) to the next transmit packet.
Back-Off Algorithm
The KSZ8851SNL implements the IEEE standard 802.3 binary exponential back-off algorithm in half-duplex mode. After
16 collisions, the packet is dropped.
Late Collision
If a transmit packet experiences collisions after 512 bit times of the transmission, the packet is dropped.
Flow Control
The KSZ8851SNL supports standard 802.3x flow control frames on both transmit and receive sides.
On the receive side, if the KSZ8851SNL receives a pause control frame, the KSZ8851SNL will not transmit the next
normal frame until the timer, specified in the pause control frame, expires. If another pause frame is received before the
current timer expires, the timer will be updated with the new value in the second pause frame. During this period (while it
is flow controlled), only flow control packets from the KSZ8851SNL are transmitted.
On the transmit side, the KSZ8851SNL has intelligent and efficient ways to determine when to invoke flow control. The
flow control is based on availability of the system resources.
There are three programmable low watermark register FCLWR (0xB0), high watermark register FCHWR (0xB2) and
overrun watermark register FCOWR (0xB4) for flow control in RXQ FIFO. The KSZ8851SNL will send PAUSE frame
when the RXQ buffer hit the high watermark level (default 3.072 KByte available) and stop PAUSE frame when the RXQ
buffer hit the low watermark level (default 5.12 KByte available). The KSZ8851SNL will drop packet when the RXQ buffer
hit the overrun watermark level (default 256-Byte available).
The KSZ8851SNL issues a flow control frame (Xoff, or transmitter off), containing the maximum pause time defined in
IEEE standard 802.3x. Once the resource is freed up, the KSZ8851SNL sends out the another flow control frame (Xon, or
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-ADF4007EBZ1 | BOARD EVALUATION FOR ADF4007EB1 |
| V110C12C100B | CONVERTER MOD DC/DC 12V 100W |
| DWP-125-3/4-0-STK | HEATSHRINK POLY 3/4"X4' BLK |
| EBA30DRMD | CONN EDGECARD 60POS .125 SQ WW |
| H2MXH-2618M | DIP CABLE - HDM26H/AE26M/X |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8851SNL-EVAL | 制造商:Micrel Inc 功能描述:BOARD EVALUATION FOR KSZ8851SNL |
| KSZ8851SNLI TR | 功能描述:以太網 IC 10/100BT Ethernet MAC + PHY with SPI Bus Interface (I-Temp, Lead free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8851SNLITR | 制造商:Micrel 功能描述:Ethernet Controller Single Chip 100Mbps |
| KSZ8851SNLI-TR | 功能描述:Ethernet Controller 10/100 Base-T/TX PHY SPI Interface 32-MLF? (5x5) 制造商:microchip technology 系列:- 包裝:剪切帶（CT） 零件狀態:有效 協議:以太網 功能:控制器 接口:SPI 標準:10/100 Base-T/TX PHY 電壓 - 電源:1.8V，2.5V，3.3V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 封裝/外殼:32-VFQFN 裸露焊盤，32-MLF? 供應商器件封裝:32-MLF?（5x5） 標準包裝:1 |
| KSZ8851SNLTR | 制造商:Micrel Inc 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。