參數資料
| 型號： | KSZ8851-32MQLI |
| 廠商： | Micrel Inc |
| 文件頁數： | 17/88頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CTLR MAC/PHY NON PCI 128PQFP |
| 標準包裝： | 66 |
| 控制器類型： | 以太網控制器，MAC/PHY |
| 接口： | 總線 |
| 電源電壓： | 1.8V，2.5V，3.3V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 128-BFQFP |
| 供應商設備封裝： | 128-PQFP（14x20） |
| 包裝： | 托盤 |
| 其它名稱： | 576-3630 KSZ8851-32MQLI-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁
Micrel, Inc.
KSZ8851-16/32 MQL/MQLI
August 2009
24
M9999-083109-2.0
Detection of Linkup
Link status wake events are useful to indicate a linkup in the network’s connectivity status.
Wake-up Packet
Wake-up packets are certain types of packets with specific CRC values that a system recognizes as a ‘wake up’ frame.
The KSZ8851M supports up to four users defined wake-up frames as below:
1. Wake-up frame 0 is defined in wakeup frame registers (0x30 – 0x3B) and is enabled by bit 0 in wakeup frame control
register (0x2A).
2. Wake-up frame 1 is defined in wakeup frame registers (0x40 – 0x4B) and is enabled by bit 1 in wakeup frame control
register (0x2A).
3. Wake-up frame 2 is defined in wakeup frame registers (0x50 – 0x5B) and is enabled by bit 2 in wakeup frame control
register (0x2A).
4. Wake-up frame 3 is defined in wakeup frame registers (0x60 – 0x6B) and is enabled by bit 3 in wakeup frame control
register (0x2A).
Magic Packet
Magic Packet technology is used to remotely wake up a sleeping or powered off PC on a LAN. This is accomplished by
sending a specific packet of information, called a Magic Packet frame, to a node on the network. When a PC capable of
receiving the specific frame goes to sleep, it enables the Magic Packet RX mode in the LAN controller, and when the LAN
controller receives a Magic Packet frame, it will alert the system to wake up.
Magic Packet is a standard feature integrated into the KSZ8851M. The controller implements multiple advanced power-
down modes including Magic Packet to conserve power and operate more efficiently.
Once the KSZ8851M has been put into Magic Packet Enable mode (WFCR[7]=1), it scans all incoming frames addressed
to the node for a specific data sequence, which indicates to the controller this is a Magic Packet (MP) frame.
A Magic Packet frame must also meet the basic requirements for the LAN technology chosen, such as Source Address
(SA), Destination Address (DA), which may be the receiving station’s IEEE address or a multicast or broadcast address
and CRC.
The specific sequence consists of 16 duplications of the IEEE address of this node, with no breaks or interruptions. This
sequence can be located anywhere within the packet, but must be preceded by a synchronization stream. The
synchronization stream allows the scanning state machine to be much simpler. The synchronization stream is defined as
6 bytes of FFh. The device will also accept a broadcast frame, as long as the 16 duplications of the IEEE address match
the address of the machine to be awakened.
Example:
If the IEEE address for a particular node on a network is 11h 22h, 33h, 44h, 55h, 66h, the LAN controller would be
scanning for the data sequence (assuming an Ethernet frame):
DESTINATION SOURCE – MISC - FF FF FF FF FF FF - 11 22 33 44 55 66 - 11 22 33 44 55 66 - 11 22 33 44 55 66 -
11 22 33 44 55 66 - 11 22 33 44 55 66 - 11 22 33 44 55 66 - 11 22 33 44 55 66 - 11 22 33 44 55 66 - 11 22 33 44 55 66 -
11 22 33 44 55 66 - MISC - CRC.
There are no further restrictions on a Magic Packet frame. For instance, the sequence could be in a TCP/IP packet or an
IPX packet. The frame may be bridged or routed across the network without affecting its ability to wake-up a node at the
frame’s destination.
If the LAN controller scans a frame and does not find the specific sequence shown above, it discards the frame and takes
no further action. If the KSZ8851M controller detects the data sequence, however, it then alerts the PC’s power
management circuitry (assert the PME pin) to wake up the system.
Physical Layer Transceiver (PHY)
100BASE-TX Transmit
The 100BASE-TX transmit function performs parallel-to-serial conversion, 4B/5B coding, scrambling, NRZ-to-NRZI
conversion, and MLT3 encoding and transmission.
The circuitry starts with a parallel-to-serial conversion, which converts the MII data from the MAC into a 125MHz serial bit
相關PDF資料 |
PDF描述 |
|---|---|
| KSZ8851-32MQL | IC CTLR MAC/PHY NON PCI 128PQFP |
| KSZ8851SNLI TR | IC ETHERNET CTLR 1PORT PCI 32MLF |
| KSZ8862-16MQL | IC SWITCH 10/100 16BIT 128-PQFP |
| KSZ8862-32MQL | IC ETHERNET SW 2PORT BUS 128PQFP |
| KSZ8863MLLI | IC ETHERNET SWITCH 3PORT 48-LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8851MLL | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Single Port MAC/PHY Controller with Non PCI Interface |
| KSZ8851MQL | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Single Port MAC/PHY Controller with Non PCI Interface |
| KSZ8851SNL | 功能描述:IC CTLR MAC/PHY NON-PCI 32-QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A |
| KSZ8851SNL TR | 功能描述:以太網 IC Single Ethernet Port + SPI Bus Interface (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8851SNL-BBE-EVAL | 功能描述:BOARD EVAL MAC/PHY FOR KSZ8851 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:LinkMD® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 主要目的:電源管理，電池充電器 嵌入式:否 已用 IC / 零件:MAX8903A 主要屬性:1 芯鋰離子電池 次要屬性:狀態 LED 已供物品:板 |
發布緊急采購，3分鐘左右您將得到回復。