參數資料
型號： ISL12025
廠商： Intersil Corporation
英文描述： Real-Time Clock/Calendar with EEPROM(EEPROM實時時鐘/日歷)
中文描述： 實時時鐘/日歷（EEPROM的實時時鐘/日歷帶有EEPROM）
文件頁數： 14/27頁
文件大?。?/td> 412K
代理商： ISL12025
14
FN6371.2
October 19, 2007
Alarm 1 and AL0 for Alarm 0), indicate if an alarm has
happened. The AL1 and AL0 bits in the status register are
reset by the falling edge of the eighth clock of status register
read.
There are two alarm operation modes: Single Event and
periodic Interrupt Mode:
1.
Single Event Mode
is enabled by setting the AL0E or
AL1E bit to “1”, the IM bit to “0”, and disabling the
frequency output. This mode permits a one-time match
between the alarm registers and the RTC registers. Once
this match occurs, the AL0 or AL1 bit is set to “1”. Once
the AL0 or AL1 bit is read, this will automatically resets it.
Both Alarm registers can be set at the same time to
trigger alarms. Polling the SR will reveal which alarm has
been set.
2.
Interrupt Mode
(or “Pulsed Interrupt Mode” or PIM) is
enabled by setting the AL0E or AL1E bit to “1” the IM bit
to “1”, and disabling the frequency output. If both AL0E
and AL1E bits are set to 1, then only the AL0E PIM alarm
will function (AL0E overrides AL1E). This means that
once the Interrupt Mode alarm is set, it will continue to
alarm for each occurring match of the alarm and present
time. This mode is convenient for hourly or daily
hardware interrupts in microcontroller applications such
as security cameras or utility meter reading. Interrupt
Mode CANNOT be used for general periodic alarms,
however, since a specific time period cannot be
programmed for interrupt, only matches to a specific time
of day. The Interrupt Mode is only stopped by disabling
the IM bit or the Alarm Enable bits.
Writing to the Alarm Registers
The Alarm Registers are non-volatile but require special
attention to insure a proper non-volatile write takes place.
Specifically, byte writes to individual registers are good for all
but registers 0006h and 0000Eh, which are the DWA0 and
DWA1 registers, respectively. Those registers will require a
special page write for nonvolatile storage. The
recommended page write sequences are as follows:
1.
16-byte page writes:
The best way to write or update the
Alarm Registers is to perform a 16-byte write beginning at
address 0001h (MNA0) and wrapping around and ending
at address 0000h (SCA0). This will insure that non-
volatile storage takes place. This means that the code
must be designed so that the Alarm0 data is written
starting with Minutes register, and then all the Alarm1
data, with the last byte being the Alarm0 Seconds (the
page ends at the Alarm1 Y2k register and then wraps
around to address 0000h).
Alternatively, the 16-byte page write could start with
address 0009h, wrap around and finish with address
0008h. Note that any page write ending at address
0007h or 000Fh (the highest byte in each Alarm) will not
trigger a nonvolatile write, so wrapping around or
overlapping to the following Alarm's Seconds register is
advised.
2.
Other nonvolatile writes:
It is possible to do writes of
less than an entire page, but the final byte must always
be addresses 0000h through 0004h or 0008h though
000Ch to trigger a nonvolatile write. Writing to those
blocks of 5 bytes sequentially, or individually, will trigger a
nonvolatile write. If the DWA0 or DWA1 registers need to
be set, then enough bytes will need to be written to
overlap with the other Alarm register and trigger the
nonvolatile write. For Example, if the DWA0 register is
being set, then the code can start with a multiple byte
write beginning at address 0006h, and then write 3 bytes
ending with the SCA1 register as follows:
Addr Name
0006h DWA0
0007h Y2K0
0008h SCA1
If the Alarm1 is used, SCA1 would need to have the correct
data written.
Power Control Operation
The power control circuit accepts a V
DD
and a V
BAT
input.
Many types of batteries can be used with Intersil RTC
products. For example, 3.0V or 3.6V Lithium batteries are
appropriate, and battery sizes are available that can power
an Intersil RTC device for up to 10 years. Another option is
to use a SuperCap for applications where V
DD
is interrupted
for up to a month. See the “Application Section” on page 21
for more information.
There are two options for setting the change-over conditions
from V
DD
to Battery Backup Mode. The BSW bit in the PWR
register controls this operation.
- Option 1 - Standard Mode
- Option 2 - Legacy Mode (Default)
Note that the I
2
C bus may or may not be operational during
battery backup, which is controlled by the SBIB bit. See
“Backup Battery Operation” on page 23 for information.
Note that switching to battery backup initiates a
three-second timeout period, during which the device will
stay in Battery Backup Mode, even if the V
DD
resumes
normal power. The three-second delay is intended to lock
out any power-up glitches that could cause communications
errors. Also note that very fast (<10μs) power ramp rates will
bypass this delay, so it is important to filter V
DD
well.
OPTION 1 - STANDARD (POWER CONTROL) MODE
In the Standard Mode, the supply will switch over to the
battery when V
DD
drops below V
TRIP
or V
BAT
, whichever is
lower. In this mode, accidental operation from the battery is
prevented since the battery backup input will only be used
when the V
DD
supply is shut off.
To select Option 1, BSW bit in the Power Register must be
set to “BSW = 0”. A description of power switchover follows.
ISL12025
相關PDF資料
PDF描述
ISL1209IU10 Low Power RTC with Battery Backed SRAM and Event Detection
ISL1209IU10Z-TK Hook-Up Wire; Conductor Size AWG:18; No. Strands x Strand Size:19 x 30; Jacket Color:Purple; Approval Bodies:UL; Approval Categories:UL AWM Style 1180; Passes VW-1 Flame Test; Cable/Wire MIL SPEC:MIL-W-16878/5 Type EE RoHS Compliant: Yes
ISL1209 Low Power RTC with Battery Backed SRAM and Event Detection
ISL1209IU10-TK Low Power RTC with Battery Backed SRAM and Event Detection
ISL1209IU10Z Low Power RTC with Battery Backed SRAM and Event Detection
相關代理商/技術參數
參數描述
ISL12025IBZ 功能描述:實時時鐘 REAL TIME CLK/CLNDR W/EEPROM 2 63VSET RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
ISL12025IBZ-T 功能描述:實時時鐘 REAL TIME CLK/CLNDR W/EEPROM 2 63VSET RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
ISL12025IVZ 功能描述:實時時鐘 REAL TIME CLK/CLNDR W/EEPROM 2 63SET 8 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
ISL12025IVZ-T 功能描述:實時時鐘 REAL TIME CLK/CLNDR W/EEPROM 2 63SET 8 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
ISL12026 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Real Time Clock/Calendar with I2C Bus? and EEPROM
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*