- 您現在的位置：買賣IC網 > PDF目錄385399 > HT46C23 (Holtek Semiconductor Inc.) A/D Type 8-Bit MCU PDF資料下載
參數資料
| 型號： | HT46C23 |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | A/D Type 8-Bit MCU |
| 中文描述： | 的A / D型8位微控制器 |
| 文件頁數： | 12/48頁 |
| 文件大?。?/td> | 348K |
| 代理商： | HT46C23 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
HT46R23/HT46C23
Rev. 1.60
12
May 3, 2004
Power Down Operation
HALT
The HALT mode is initialized by the HALT instruction
and results in the following...
The system oscillator will be turned off but the WDT
oscillator keeps running (if the WDT oscillator is se-
lected).
The contents of the on chip RAM and registers remain
unchanged.
WDT will be cleared and recounted again (if the WDT
clock is from the WDT oscillator).
All of the I/O ports maintain their original status.
The PDF flag is set and the TO flag is cleared.
The system can leave the HALT mode by means of an
external reset, an interrupt, an external falling edge sig-
nal on port A or a WDT overflow. An external reset
causes a device initialization and the WDToverflow per-
forms a warm reset . After the TO and PDF flags are
examined, the reason for chip reset can be determined.
The PDF flag is cleared by system power-up or execut-
ing the CLR WDT instruction and is set when execut-
ing the HALT instruction. The TO flag is set if the WDT
time-out occurs, and causes a wake-up that only resets
the PC and SP; the others keep their original status.
The port A wake-up and interrupt methods can be con-
sidered as a continuation of normal execution. Each bit
in port A can be independently selected to wake up the
device by the options. Awakening from an I/O port stim-
ulus, the program will resume execution of the next in-
struction. If it is awakening from an interrupt, two
sequences may happen. If the related interrupt is dis-
abled or the interrupt is enabled but the stack is full, the
program will resume execution at the next instruction. If
theinterruptisenabledandthestackisnotfull,theregu-
lar interrupt response takes place. If an interrupt request
flag is set to 1 before entering the HALT mode, the
wake-upfunctionoftherelatedinterruptwillbedisabled.
Once a wake-up event occurs, it takes 1024 t
SYS
(sys-
tem clock period) to resume normal operation. In other
words, a dummy period will be inserted after wake-up. If
the wake-up results from an interrupt acknowledgment,
the actual interrupt subroutine execution will be delayed
by one or more cycles. If the wake-up results in the next
instruction execution, this will be executed immediately
after the dummy period is finished.
To minimize power consumption, all the I/O pins should
be carefully managed before entering the HALT status.
Reset
Therearethreewaysinwhicharesetcanoccur:
RES reset during normal operation
RES reset during HALT
WDT time-out reset during normal operation
The WDT time-out during HALT is different from other
chip reset conditions, since it can perform a warm re -
set that resets only the PC and SP, leaving the other
circuits in their original state. Some registers remain un-
changed during other reset conditions. Most registers
are reset to the initial condition when the reset condi-
tions are met. By examining the PDF and TO flags, the
programcandistinguishbetweendifferent chipresets .
TO
PDF
RESET Conditions
0
0
RES reset during power-up
u
u
RES reset during normal operation
0
1
RES wake-up HALT
1
u
WDT time-out during normal operation
1
1
WDT wake-up HALT
Note: u means unchanged
To guarantee that the system oscillator is started and
stabilized, the SST (System Start-up Timer) provides an
extra-delay of 1024 system clock pulses when the sys-
tem reset (power-up, WDT time-out or RES reset) or the
system awakes from the HALT state.
$
" 4
+ $ #
" ( "
Reset Timing Chart
=
=
D
1 E
D
1 E
Reset Circuit
Note:
* Make the length of the wiring, which is con-
nected to the RES pin as short as possible, to
avoid noise interference.
" ( "
>
*
. )
" ( "
' ( "
" ( "
4 @ $
$ # # . "
! "
Reset Configuration
相關PDF資料 |
PDF描述 |
|---|---|
| HT46C24 | A/D Type 8-Bit MCU |
| HT46R24 | A/D Type 8-Bit MCU |
| HT46C46 | Cost-Effective A/D Type 8-Bit MCU |
| HT46C47 | Cost-Effective A/D Type 8-Bit MCU |
| HT46R46 | Cost-Effective A/D Type 8-Bit MCU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT46C232 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:A/D Type 8-Bit MCU |
| HT46C24 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:A/D Type 8-Bit MCU |
| HT46C46 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Cost-Effective A/D Type 8-Bit MCU |
| HT46C46E | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Cost-Effective A/D Type 8-Bit MCU |
| HT46C47 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Cost-Effective A/D Type 8-Bit MCU |
發布緊急采購，3分鐘左右您將得到回復。