- 您現在的位置：買賣IC網 > PDF目錄385396 > HSP50110JI-52 (HARRIS SEMICONDUCTOR) Digital Quadrature Tuner PDF資料下載
參數資料
| 型號： | HSP50110JI-52 |
| 廠商： | HARRIS SEMICONDUCTOR |
| 元件分類： | 通信及網絡 |
| 英文描述： | Digital Quadrature Tuner |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PQCC84 |
| 文件頁數： | 5/24頁 |
| 文件大小： | 199K |
| 代理商： | HSP50110JI-52 |
3-233
processing elements so that they are enabled once for each
time ENI is sampled low. This mode minimizes the
processing pipeline latency, and the latency of the part’s
serial interfaces while conserving power.
Note: the
effective input sample rate to the internal processing
elements is equal to the frequency with which ENI is
asserted “l(fā)ow”.
In Interpolated Input Mode, the ENI input is used to insert
zeroes between the input data samples. This process
increases the input sample rate to the processing elements
which improves the time resolution of the processing chain.
When ENI is sampled “high” by CLK, a zero is input into the
processing pipeline. When ENI is sampled “l(fā)ow” the input
data is fed into the pipeline.
Note: Due to the nature of the
rate change operation, consideration must be given to
the scaling and interpolation filtering required for a
particular rate change factor.
In either the Gated or Interpolated Input Mode, the
Synthesizer NCO is gated by the ENI input. This only allows
clocking of the NCO when external samples are input to the
processing pipeline. As a result, the NCO frequency must be
set relative to the input sample rate, not the CLK rate (see
Synthesizer/Mixer Section).
NOTE: Only fixed
interpolation rates should be used when operating the
part in Interpolated Mode at the Input Controller.
Input Level Detector
The Input Level Detector generates a one-bit error signal for
an external IF AGC filter and amp. The error signal is
generated by comparing the magnitude of the input samples
to a user programmable threshold. The HI/LO pin is then
driven “high” or “l(fā)ow” depending the relationship of its
magnitude to the threshold. The sense of the HI/LO pin is
programmable so that a magnitude exceeding the threshold
can either be represented as a “high” or “l(fā)ow” logic state.
The threshold and the sense of the HI/LO pin are configured
by loading the appropriate control registers via the
Microprocessor Interface (see Tables 8 and 12).
The high/low outputs can be integrated by an external loop
filter to close an AGC loop. Using this method the gain of the
loop forces the median magnitude of the input samples to
the threshold. When the magnitude of half the samples are
above the threshold and half are below, the error signal is
integrated to zero by the loop filter.
The algorithm for determining the magnitude of the complex
input is given by:
Mag(I,Q) = |I| + .375 x |Q| if |I| > |Q|
(EQ. 1)
or:
Mag(I,Q) = |Q| + .375 x |I| if |Q| > |I|,
(EQ. 2)
Using this algorithm, the magnitude of complex inputs can
be estimated with an error of <0.55dB or approximately
6.5%. For real inputs, the magnitude detector reduces to a
an absolute value detector with negligible error.
Note: an external AGC loop using the Input Level
Detector may go unstable for a real sine wave input
whose frequency is exactly one quarter of the sample
rate (F
S
/4). The Level Detector responds to such an
input by producing a square wave output with a 50%
duty cycle for a wide range of thresholds. This square
wave integrates to zero, indicating no error for a range
of input signal amplitudes.
Synthesizer/Mixer
The Synthesizer/Mixer spectrally shifts the input signal of
interest to DC for subsequent baseband filtering. This
function is performed by using a complex multiplier to
multiply the input with the output of a quadrature numerically
controlled oscillator (NCO). The multiplier operation is:
I
OUT
= I
IN
x cos (
ω
c
) - Q
IN
x sin (
ω
c
)
Q
OUT
= I
IN
x sin (
ω
c
) + Q
IN
x cos (
ω
c
)
The complex multiplier output is rounded to 12 bits. For real
inputs this operation is similar to that performed by a
quadrature downconverter. For complex inputs, the
Synthesizer/Mixer functions as a single-sideband or image
reject mixer which shifts the frequency of the complex
samples without generating images.
(EQ. 3)
(EQ. 4)
SHIFT REG
SYNC
REG
SYNC
CFLD
COF
COFSYNC
SIN/COS
ROM
REG
REG
TO COMPLEX MULTIPLIER
COS
10
SIN
PH0-1
LOTP
CARRIER
FREQUENCY
LOAD CARRIER
FREQUENCY
PHASE OFFSET
32
32
8
2
10
MUX
0
COF
ENABLE
MUX
0
LOAD
PHASE
ACCUMULATOR
CF
COF
R
E
G
REG
+
REG
+
REG
R
E
G
R
E
G
Controlled via
microprocessor interface.
FIGURE 2. SYNTHESIZER NCO
11
HSP50110
相關PDF資料 |
PDF描述 |
|---|---|
| HSP50110JC-52 | CONN HEADER HM 2MM 100POS |
| HSP50110 | Digital Quadrature Tuner(數字調諧器) |
| HSP50210 | Digital Costas Loop(數字Costas鎖相環) |
| HSP50214VC | Programmable Downconverter |
| HSP50214VI | Programmable Downconverter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HSP50110JI-52Z | 制造商:Intersil Corporation 功能描述:PB-FREE W/ANNEAL DIGITAL QUADRATURE TUNER 84 PLCC,52MHZ,INDU - Rail/Tube |
| HSP50210 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Digital Costas Loop |
| HSP50210JC-52 | 功能描述:上下轉換器 COSTAS DEMODULATOR,84 PLCC,52MHZ,COMM RoHS:否 制造商:Texas Instruments 產品:Down Converters 射頻:52 MHz to 78 MHz 中頻:300 MHz LO頻率: 功率增益: P1dB: 工作電源電壓:1.8 V, 3.3 V 工作電源電流:120 mA 最大功率耗散:1 W 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-128 |
| HSP50210JC-52Z | 功能描述:上下轉換器 COSTAS DEMODULATOR 84 PLCC 52MHZ COM RoHS:否 制造商:Texas Instruments 產品:Down Converters 射頻:52 MHz to 78 MHz 中頻:300 MHz LO頻率: 功率增益: P1dB: 工作電源電壓:1.8 V, 3.3 V 工作電源電流:120 mA 最大功率耗散:1 W 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-128 |
| HSP50210JI-52 | 功能描述:上下轉換器 COSTAS DEMODULATOR,84 PLCC,52MHZ,IND RoHS:否 制造商:Texas Instruments 產品:Down Converters 射頻:52 MHz to 78 MHz 中頻:300 MHz LO頻率: 功率增益: P1dB: 工作電源電壓:1.8 V, 3.3 V 工作電源電流:120 mA 最大功率耗散:1 W 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-128 |
發布緊急采購，3分鐘左右您將得到回復。