- 您現在的位置：買賣IC網 > PDF目錄384324 > GC1012A-CQ (Texas Instruments, Inc.) DIGITAL TUNER CHIP PDF資料下載
參數資料
| 型號： | GC1012A-CQ |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | DIGITAL TUNER CHIP |
| 中文描述： | 數字調諧器芯片 |
| 文件頁數： | 8/30頁 |
| 文件大小： | 186K |
| 代理商： | GC1012A-CQ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
GRAYCHIP,INC.
- 3 -
FEBRUARY 18, 1998
GC1012A DIGITAL TUNER
DATA SHEET REV 0.1
This document contains information which may be changed at any time without notice
Control register addresses 12, 13, 14, and 15 are reserved to allow an external processor to read
output samples from the chip. Addresses 12 and 13 are the I-registers which store the16 bit
in-phase part
of the output sample. Addresses 14 and 15 are the Q-registers which store the quadrature part. In the real
mode the I registers store the even-time output samples and the Q registers store the odd-time output
samples. Output ready and missed flags are provided in control register 9 in order to synchronize the storing
and reading of the output samples. An interrupt output pin is also provided on the chip which can be used
to interrupt the external processor when a new sample is ready. See the description of control register 9 in
Section 3.6 for more details. The setup, hold and pulse width requirements for control read or write
operations are given in Section 4.4.
Checksums are read from the chip during diagnostics using address 11. More details on the
diagnostic modes is given in Section 1.11.
Address 10 is used to generate a one-shot pulse on the
OS
output pin. This pulse can be used to
synchronize the output timing and/or frequency oscillators of multiple GC1012A chips.
The control interface also generates the chips internal sync strobes. The user may select to
synchronize the chip using an external sync strobe (
SS
), or use the chips internal sync counter. The internal
sync counter can be synchronized to
SS
, or left to free run (See
SS_OFF
in Section 3.2). The period of the
internal sync counter can be either 256 clocks or 2
20
clocks. The 256 clock period is intended to be used
for chip test purposes only. The internal sync counter is used during diagnostics to clear the data paths and
strobe the checksum generator. The internal sync counter can also be used to periodically re-synchronize
all of the counters in the chip during normal operating modes.
1.4
DIGITAL OSCILLATOR
The digital oscillator generates sine and cosine sequences which are used to mix the desired signal
down to zero frequency. The digital oscillator contains a 28 bit frequency register, a 28 bit frequency
accumulator, and a sine-cosine generator. The tuning frequency of the oscillator is set by loading a 28 bit
frequency word from the control registers into the frequency register. If the frequency register is set to the
word
FREQ
, then the tuning frequency will be:
. The tuning frequency
should be set to the middle of the desired output bandwidth.
The frequency word
FREQ
is stored into the control registers at control addresses 0,1,2 and 3. The
28 bit word is then transferred into the frequency register using one of the following methods:
(1)
The frequency register is always loading (the frequency changes immediately as the
frequency word is loaded into the control registers).
(2)
The frequency register is loaded when the user sets a control register bit.
(3)
The frequency register is synchronously loaded when the accumulator sync strobe (
low.
AS
) goes
(4)
The frequency register is synchronously loaded when the system sync strobe (
SS
) goes low.
See Section 3.2 for more details on the frequency load modes.
Frequency
2
28
----------------------------------
FREQ
=
相關PDF資料 |
PDF描述 |
|---|---|
| GC5051 | PARAGON⑩ DIGITAL Four Channel DSP System with FRONTWAVE |
| GC5057 | PARAGON⑩ DIGITAL Four Channel DSP System with FRONTWAVE |
| GCDA05 | Time-Delay Relay; Contacts:DPDT; Time Range:1.2 to 120s; Mounting Type:Plug-In; Timing Function:Delay-On-Dropout; Contact Carrying Power:2VA |
| GCDA15C-1-GS08 | Low Capacitance Bidirectional ESD Protection Diodes |
| GD65232DBR | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GC1012A-PQ | 制造商:TI 制造商全稱:Texas Instruments 功能描述:DIGITAL TUNER CHIP |
| GC1012B | 制造商:TI 制造商全稱:Texas Instruments 功能描述:3.3V DIGITAL TUNER CHIP |
| GC1012B_07 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:3.3V DIGITAL TUNER CHIP |
| GC1012B-PQ | 功能描述:調諧器 Sgl channel WB DDC RoHS:否 制造商:NXP Semiconductors 功能: 噪聲系數: 工作電源電壓: 最小工作溫度: 最大工作溫度: |
| GC1012B-PQA | 制造商:TI 制造商全稱:Texas Instruments 功能描述:3.3V DIGITAL TUNER CHIP |
發布緊急采購，3分鐘左右您將得到回復。