- 您現在的位置：買賣IC網 > PDF目錄384324 > GC1012A-CQ (Texas Instruments, Inc.) DIGITAL TUNER CHIP PDF資料下載
參數資料
| 型號： | GC1012A-CQ |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | DIGITAL TUNER CHIP |
| 中文描述： | 數字調諧器芯片 |
| 文件頁數： | 7/30頁 |
| 文件大小： | 186K |
| 代理商： | GC1012A-CQ |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
GRAYCHIP,INC.
- 2 -
FEBRUARY 18, 1998
GC1012A DIGITAL TUNER
DATA SHEET REV 0.1
This document contains information which may be changed at any time without notice
1.2
BLOCK DIAGRAM
A block diagram illustrating the major functions of the chip is shown in Figure 1
Figure 1. GC1012A Block Diagram
Each of these functions are described below.
1.3
CONTROL INTERFACE
The control interface performs four major functions: It allows an external processor to configure the
chip, it allows an external processor to capture and read output samples from the chip, it allows an external
processor to perform diagnostics, and it generates internal synchronization strobes.
The chip is configured by writing control information into 8 bit control registers within the chip. The
contents of these control registers and how to use them are described in Section 3. The registers are written
to or read from using the
C[0:7]
,
A[0:3]
,
R/W
, and
CS
pins. Each control register has been assigned a
unique address within the chip. An external processor (a microprocessor, computer, or DSP chip) can write
into a register by setting
A[0:3]
to the desired register address, setting the
R/W
pin low, setting
D[0:7]
to
the desired value and then pulsing
CS
low.
To read from a control register the processor must set
A[0:3]
to the desired address, set
R/W
high,
and then set
CS
low. The chip will then drive
C[0:7]
with the contents of the selected register. After the
processor has read the value from
C[0:7]
it should set
CS
high. The
C[0:7]
pins are turned off (high
impedance) whenever
CS
is high or
R/W
is low. The chip will only drive these pins when
CS
is low and
R/W
is high.
M
DIAG-
NOSTIC
RAMP
DIGITAL
OSCILLATOR
COS
SIN
DIAG
SELECT
FREQ
PROGRAMMABLE
LOW PASS
FILTER
GAIN
ADJUST
OUTPUT
FORMAT
CHECKSUM
GAIN
I/Q
SAMPLES
BANDWIDTH
CONTROL INTERFACE
C0-C7
A0-A3
R/W
CS
REAL,
FLIP
CHECKSUM
I
Q
(10,12,14, OR 16 BITS)
STROBES
(WS,IFLAG)
SYNCS OUT
(SO,OS,INT,OFLOW)
CK
SYNCS IN
SS,AS,GS)
X
VCC
GND
AND
OFFSET
OUTPUTS
OPTIONS
(12 BITS)
相關PDF資料 |
PDF描述 |
|---|---|
| GC5051 | PARAGON⑩ DIGITAL Four Channel DSP System with FRONTWAVE |
| GC5057 | PARAGON⑩ DIGITAL Four Channel DSP System with FRONTWAVE |
| GCDA05 | Time-Delay Relay; Contacts:DPDT; Time Range:1.2 to 120s; Mounting Type:Plug-In; Timing Function:Delay-On-Dropout; Contact Carrying Power:2VA |
| GCDA15C-1-GS08 | Low Capacitance Bidirectional ESD Protection Diodes |
| GD65232DBR | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GC1012A-PQ | 制造商:TI 制造商全稱:Texas Instruments 功能描述:DIGITAL TUNER CHIP |
| GC1012B | 制造商:TI 制造商全稱:Texas Instruments 功能描述:3.3V DIGITAL TUNER CHIP |
| GC1012B_07 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:3.3V DIGITAL TUNER CHIP |
| GC1012B-PQ | 功能描述:調諧器 Sgl channel WB DDC RoHS:否 制造商:NXP Semiconductors 功能: 噪聲系數: 工作電源電壓: 最小工作溫度: 最大工作溫度: |
| GC1012B-PQA | 制造商:TI 制造商全稱:Texas Instruments 功能描述:3.3V DIGITAL TUNER CHIP |
發布緊急采購，3分鐘左右您將得到回復。