- 您現在的位置：買賣IC網 > PDF目錄384280 > EDE5108AJBG-8E-E (ELPIDA MEMORY INC) 512M bits DDR2 SDRAM PDF資料下載
參數資料
| 型號： | EDE5108AJBG-8E-E |
| 廠商： | ELPIDA MEMORY INC |
| 元件分類： | DRAM |
| 英文描述： | 512M bits DDR2 SDRAM |
| 中文描述： | 64M X 8 DDR DRAM, 0.4 ns, PBGA60 |
| 封裝： | ROHS COMPLIANT, FBGA-60 |
| 文件頁數： | 47/77頁 |
| 文件大?。?/td> | 589K |
| 代理商： | EDE5108AJBG-8E-E |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁當前第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁
EDE5108AJBG, EDE5116AJBG
Preliminary Data Sheet E1044E20 (Ver. 2.0)
47
Bank Activate Command [ACT]
The bank activate command is issued by holding /CAS and /WE high with /CS and /RAS low at the rising edge of the
clock. The bank addresses BA0 and BA1, are used to select the desired bank. The row address A0 through A13 is
used to determine which row to activate in the selected bank. The Bank activate command must be applied before
any read or write operation can be executed. Immediately after the bank active command, the DDR2 SDRAM can
accept a read or write command on the following clock cycle. If a R/W command is issued to a bank that has not
satisfied the tRCD (min.) specification, then additive latency must be programmed into the device to delay when the
R/W command is internally issued to the device. The additive latency value must be chosen to assure tRCD (min.)
is satisfied. Additive latencies of 0, 1, 2, 3 and 4 are supported. Once a bank has been activated it must be
precharged before another bank activate command can be applied to the same bank. The bank active and
precharge times are defined as tRAS and tRP, respectively. The minimum time interval between successive bank
activate commands to the same bank is determined by the /RAS cycle time of the device (tRC), which is equal to
tRAS + tRP. The minimum time interval between successive bank activate commands to the different bank is
determined by (tRRD).
/CK
CK
Address
Command
T0
T1
T2
T3
Tn
Tn+1
Tn+2
Tn+3
tRCD(min.)
tRAS
tRP
tRC
ROW: 0
ACT
Bank0
Active
Bank Activate Command Cycle (tRCD = 3, AL = 2, tRP = 3, tRRD = 2, tCCD = 2)
Bank1
Active
Bank0
Active
Bank0
Precharge
Bank1
Precharge
Posted
READ
Posted
READ
ACT
PRE
PRE
ACT
COL: 0
ROW: 0
ROW: 1
COL: 1
tCCD
Additive latency (AL)
tRRD
Bank0 Read begins
相關PDF資料 |
PDF描述 |
|---|---|
| EDE5116AJBG | 512M bits DDR2 SDRAM |
| EDE5116AJBG-6E-E | 512M bits DDR2 SDRAM |
| EDE5116AJBG-8E-E | 512M bits DDR2 SDRAM |
| EDE702 | Serial LCD Interface IC |
| EDI8808CB | HIGH SPEED, LOW POWER 64K MONOLITHIC SRAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EDE5108AJSE | 制造商:ELPIDA 制造商全稱:Elpida Memory 功能描述:512M bits DDR2 SDRAM |
| EDE5108AJSE-6E-E | 制造商:ELPIDA 制造商全稱:Elpida Memory 功能描述:512M bits DDR2 SDRAM |
| EDE5108AJSE-8E-E | 制造商:ELPIDA 制造商全稱:Elpida Memory 功能描述:512M bits DDR2 SDRAM |
| EDE5108GASA | 制造商:ELPIDA 制造商全稱:Elpida Memory 功能描述:512M bits DDR-II SDRAM |
| EDE5108GASA-4A-E | 制造商:ELPIDA 制造商全稱:Elpida Memory 功能描述:512M bits DDR-II SDRAM |
發布緊急采購，3分鐘左右您將得到回復。