參數資料
型號： DV164136
廠商： Microchip Technology
文件頁數： 57/107頁
文件大?。?/td> 0K
描述： DEVELOPMENT KIT FOR PIC18
產品培訓模塊： PIC18 J Series MCU Overview
標準包裝： 1
系列： PIC®
類型： MCU
適用于相關產品： PIC18F8722，PIC18F87J11
所含物品： 板，線纜，CD，PICkit? 3 個編程器，電源
產品目錄頁面： 659 (CN2011-ZH PDF)
相關產品： PIC18F87J11-I/PT-ND - IC PIC MCU FLASH 64KX16 80TQFP
PIC18F87J11T-I/PTTR-ND - IC PIC MCU FLASH 64KX16 80TQFP
PIC18F8722T-E/PT-ND - IC PIC MCU FLASH 64KX16 80TQFP
PIC18F8722-E/PT-ND - IC PIC MCU FLASH 64KX16 80TQFP
PIC18F8722T-I/PT-ND - IC PIC MCU FLASH 64KX16 80TQFP
PIC18F8722-I/PT-ND - IC PIC MCU FLASH 64KX16 80TQFP
2007-2012 Microchip Technology Inc.
DS39778E-page 53
PIC18F87J11 FAMILY
4.4.3
RC_IDLE MODE
In RC_IDLE mode, the CPU is disabled but the
peripherals continue to be clocked from the internal
oscillator block. This mode allows for controllable
power conservation during Idle periods.
From RC_RUN, this mode is entered by setting the
IDLEN bit and executing a SLEEP instruction. If the
device is in another Run mode, first set IDLEN, then
clear the SCSx bits and execute SLEEP. When the
clock source is switched to the INTOSC block, the pri-
mary oscillator is shut down and the OSTS bit is
cleared.
When a wake event occurs, the peripherals continue to
be clocked from the internal oscillator block. After a
delay of TCSD following the wake event, the CPU
begins executing code being clocked by the INTRC.
The IDLEN and SCSx bits are not affected by the
wake-up. The INTRC source will continue to run if
either the WDT or the Fail-Safe Clock Monitor is
enabled.
4.5
Exiting Idle and Sleep Modes
An exit from Sleep mode, or any of the Idle modes, is
triggered by an interrupt, a Reset or a WDT time-out.
This section discusses the triggers that cause exits
from power-managed modes. The clocking subsystem
actions are discussed in each of the power-managed
modes sections (see Section 4.2 “Run Modes”,
).
4.5.1
EXIT BY INTERRUPT
Any of the available interrupt sources can cause the
device to exit from an Idle mode, or the Sleep mode, to
a Run mode. To enable this functionality, an interrupt
source must be enabled by setting its enable bit in one
of the INTCON or PIE registers. The exit sequence is
initiated when the corresponding interrupt flag bit is set.
On all exits from Idle or Sleep modes by interrupt, code
execution branches to the interrupt vector if the
GIE/GIEH bit (INTCON<7>) is set. Otherwise, code
execution continues or resumes without branching
A fixed delay of interval, TCSD, following the wake event
is required when leaving Sleep and Idle modes. This
delay is required for the CPU to prepare for execution.
Instruction execution resumes on the first clock cycle
following this delay.
4.5.2
EXIT BY WDT TIME-OUT
A WDT time-out will cause different actions depending
on which power-managed mode the device is in when
the time-out occurs.
If the device is not executing code (all Idle modes and
Sleep mode), the time-out will result in an exit from the
power-managed
mode
(see
and Section 4.3 “Sleep Mode”). If the device
is executing code (all Run modes), the time-out will
result in a WDT Reset (see Section 25.2 “Watchdog
).
The Watchdog Timer and postscaler are cleared by one
of the following events:
Executing a SLEEP or CLRWDT instruction
The loss of a currently selected clock source (if
the Fail-Safe Clock Monitor is enabled)
4.5.3
EXIT BY RESET
Exiting an Idle or Sleep mode by Reset automatically
forces the device to run from the INTRC.
4.5.4
EXIT WITHOUT AN OSCILLATOR
START-UP DELAY
Certain exits from power-managed modes do not
invoke the OST at all. There are two cases:
PRI_IDLE mode, where the primary clock source
is not stopped
The primary clock source is either the EC or
ECPLL mode
In these instances, the primary clock source either
does not require an oscillator start-up delay, since it is
already running (PRI_IDLE), or normally does not
require an oscillator start-up delay (EC). However, a
fixed delay of interval, TCSD, following the wake event,
is still required when leaving Sleep and Idle modes to
allow the CPU to prepare for execution. Instruction
execution resumes on the first clock cycle following this
delay.
相關PDF資料
PDF描述
GBM25DCWT CONN EDGECARD 50POS DIP .156 SLD
GCM24DCTN CONN EDGECARD 48POS DIP .156 SLD
1435863-2 PATCHCORD CAT6 YLW/YLW BOOT 2'
1435862-2 PATCHCORD CAT6 RED/RED BOOT 2'
V48C5T50BF3 CONVERTER MOD DC/DC 5V 50W
相關代理商/技術參數
參數描述
DV164139 功能描述:開發板和工具包 - PIC / DSPIC Lo PIn Count USB Dev Kit (w/PICkit 3) RoHS:否 制造商:Microchip Technology 產品:Starter Kits 工具用于評估:chipKIT 核心:Uno32 接口類型: 工作電源電壓:
DV17K3225T 制造商:SEI Stackpole Electronics Inc 功能描述:- Tape and Reel 制造商:SEI Stackpole Electronics Inc 功能描述:Var MOV 17VAC/22VDC 100A 27V 3225 SMD T/R
DV17K4032T 制造商:SEI Stackpole Electronics Inc 功能描述:VAR 17VAC 22VDC 250A 27V 4032 SMD - Tape and Reel 制造商:SEI Stackpole Electronics Inc 功能描述:Var MOV 17VAC/22VDC 250A 27V 4032 SMD T/R
DV18-145MB-3K 功能描述:端子 PIN -DSC 22-18 145X032 VYL RED RoHS:否 制造商:AVX 產品:Junction Box - Wire to Wire 系列:9826 線規:26-18 接線柱/接頭大小: 絕緣: 顏色:Red 型式:Female 觸點電鍍:Tin over Nickel 觸點材料:Beryllium Copper, Phosphor Bronze 端接類型:Crimp
DV18-145M-C 功能描述:端子 MALE BLADE ADAPT RoHS:否 制造商:AVX 產品:Junction Box - Wire to Wire 系列:9826 線規:26-18 接線柱/接頭大小: 絕緣: 顏色:Red 型式:Female 觸點電鍍:Tin over Nickel 觸點材料:Beryllium Copper, Phosphor Bronze 端接類型:Crimp
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*