
MAX8660/MAX8660A/MAX8660B/MAX8661
High-Efficiency, Low-IQ, PMICs with Dynamic
Voltage Management for Mobile Applications
4
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
(VIN = VIN5 = VIN67 = VIN8 = 3.6V, Figure 3, TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 2)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Note 1: LX_ has internal clamp diodes to PG_ and PV_. Applications that forward bias these diodes must take care not to exceed
the IC’s package power-dissipation limits.
IN, IN5, IN6, IN67, EN2, EN34, EN5, LBO, RSO, MR, SET1,
SET2, V1, V2, V3, V4, SCL, SDA,
SRAD to AGND..................................................-0.3V to +7.5V
LBF, LBR, EN1, RAMP to AGND .................-0.3V to (VIN + 0.3V)
V8 to AGND................................................-0.3V to (VIN8 + 0.3V)
V5 to AGND................................................-0.3V to (VIN5 + 0.3V)
V6, V7 to AGND........................................-0.3V to (VIN67 + 0.3V)
PV1 to PG1 ............................................................-0.3V to +7.5V
PV2 to PG2 ............................................................-0.3V to +7.5V
PV3 to PG3 ............................................................-0.3V to +7.5V
PV4 to PG4 ............................................................-0.3V to +7.5V
PV, PV1, PV2, PV3, PV4, IN8 to IN ........................-0.3V to +0.3V
LX1 Continuous RMS Current (Note 1) .................................2.3A
LX2 Continuous RMS Current (Note 1) .................................2.0A
LX3 Continuous RMS Current (Note 1) .................................2.6A
LX4 Continuous RMS Current (Note 1) .................................1.0A
PG1, PG2, PG3, PG4, EP to AGND.......................-0.6V to +0.6V
GND to AGND ......................................................-0.3V to +0.3V
All REGx Output Short-Circuit Duration......................Continuous
Continuous Power Dissipation (TA = +70°C)
40-Pin Thin QFN (derate 35.7mW/°C above +70°C).....2857mW
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Soldering Temperature (reflow) .......................................+260°C
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
PV1, PV2, PV3, PV4, IN, IN8
Supply Voltage Range
VIN
PV1, PV2, PV3, PV4, IN, and IN8 must be
connected together externally
2.6
6.0
V
VIN rising
2.250
2.400
2.550
IN Undervoltage-Lockout
Threshold
VUVLO
VIN falling
2.200
2.350
2.525
V
VIN rising
6.20
6.35
6.50
IN Overvoltage-Lockout
Threshold
VOVLO
VIN falling
6.00
6.15
6.30
V
Only V8 on (deep-sleep
power mode)
20
V1, V2, and V8 on;
V1 and V2 in normal (skip)
operating mode
50
V1, V2, V5, and V8 on
(sleep power mode);
V1 and V2 in normal (skip)
operating mode
90
V1, V2, V3, V4, V5, and V8 on
(run power mode);
V1, V2, V3, and V4 in normal
(skip) operating mode
140
No load;
SDA = SCL = V8
V1, V2, V3, V4, V5, V6, V7,
and V8 (all on);
V1, V2, V3, and V4 in normal
(skip) operating mode
250
Undervoltage lockout, VIN = 2.2V
1.5
Input Current
IIN + IPV1 +
IPV2 + IPV3 +
IPV4 + IIN5 +
IIN67 + IIN8
Overvoltage lockout, VIN = 6.5V
25
A